Bedienungsanleitung Parkside PTK 2000 A1 - IAN 104416 (Seite 19 von 64) (Deutsch, Englisch, Holländisch, Französisch)

595333

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

14 GB

- Use the stop rail (e).

- Press the workpiece rmly against the cross stop (13).

- Switch on the saw.

- Push the cross stop (13) and the workpiece toward

the blade in order to make the cut.

- Important:

Always hold the guided part of the workpiece.

Never hold the part which is to be cut off.

- Push the cross stop (13) forward until the workpiece is

cut all the way through.

- Switch off the saw again. Do not remove the offcut

until the blade has stopped rotating.

10.3 Cutting particle boards

To prevent the cutting edges from cracking when work-

ing with particle boards, you should not set the saw

blade (5) more than 5mm greater than the thickness of

the workpiece (also see 9.2).

11. Transport

1. Turn off the power tool before any transport and

disconnect it from the power supply.

2. Apply the power tool at least with two people, do

not touch the table extensions.

Use only the transport handles (Figure 43/44)

punched into both sides of the housing for trans-

porting the equipment.

3. Protect the power tool from knocks, bumps and

strong vibrations, such as during transport in vehi-

cles.

4. Secure the power tool against overturning and slid-

ing.

5. Never use the safety devices for handling or trans-

porting purposes.

12. Maintenance

m Warning! Prior to any adjustment, maintenance or

service work disconnect the mains power plug!

12.1 General maintenance measures

• Keep all safety devices, air vents and the motor hous-

ing free of dirt and dust as far as possible. Wipe the

equipment with a clean cloth or blow it down with com-

pressed air at low pressure.

• We recommend that you clean the equipment imme-

diately after you use it.

• Clean the equipment regularly with a damp cloth and

some soft soap. Do not use cleaning agents or sol-

vents; these may be aggressive to the plastic parts in

the equipment. Ensure that no water can get into the

interior of the equipment.

• In order to extend the service life of the tool, oil the

rotary parts once monthly. Do not oil the motor.

12.2 Brush inspection

In case of excessive sparking, have the carbon brushes

checked only by a qualied electrician. Important. The

carbon brushes should not be replaced by anyone but a

qualied electrician.

13. Storage

Store the device and its accessories in a dark, dry and

frost-proof place that is inaccessible to children. The

optimum storage temperature is between 5 and 30˚C.

Store the electrical tool in its original packaging.

Cover the electrical tool in order to protect it from dust

and moisture.

Store the operating manual with the electrical tool.

14. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies with

the applicable VDE and DIN provisions.

The customer‘s mains connection as well as the

extension cable used must also comply with these

regulations.

• The product meets the requirements of

EN 61000-3-11 and is subject to special connec-

tion conditions. This means that use of the product

at any freely selectable connection point is not al-

lowed.

• Given unfavorable conditions in the power supply the

product can cause the voltage to uctuate temporarily.

• The product is exclusively intended for use at con-

nection points that have a continuous current-carry-

ing capacity of at least 100 Amper phase.

• As the user, you are required to ensure, in consulta-

tion with your electric power company if necessary,

that the connection point at which you wish to ope-

rate the product meets the specied requirements.

Important information

In the event of an overloading the motor will switch

itself off. After a cool-down period (time varies) the mo-

tor can be switched back on again.

Damaged electrical connection cable

The insulation on electrical connection cables is often

damaged.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been improp-

erly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insulation

damage.

Check the electrical connection cables for damage regu-

larly. Make sure that the connection cable does not hang

on the power network during the inspection.

Electrical connection cables must comply with the ap-

plicable VDE and DIN provisions. Only use connection

cables with the marking „H05VV-F“.

The printing of the type designation on the connection

cable is mandatory.

AC motor

• The mains voltage must be 230 V~

• Extension cables up to 25 m long must have a

cross-section of 1.5 mm

Connections and repairs of electrical equipment may

only be carried out by an electrician.

Please provide the following information in the event of

any enquiries:

Type of current for the motor

• Machine data - type plate

15. Disposal and recycling

The equipment is supplied in packaging to pre-

vent it from being damaged in transit. The raw

materials in this packaging can be reused or recy-

cled. Never place batteries in your household refuse, in

re or in water. Batteries should be collected, recycled or

disposed of by environment-friendly means. The equip-

Parkside PTK 2000 A1 - IAN 104416 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info