Bedienungsanleitung Parkside PTK 2000 A1 - IAN 104416 (Seite 20 von 64) (Deutsch, Englisch, Holländisch, Französisch)

595333

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

15GB

ment and its accessories are made of various types of

material, such as metal and plastic. Defective compo-

nents must be disposed of as special waste. Ask your

dealer or your local council.

17. Warranty certicate

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your

device develops a fault, please contact our service department at the address shown on this guarantee card. Of course, if you

would prefer to call us then we are also happy to offer our assistance under the service number printed below. Please note the

following terms under which guarantee claims can be made:

• These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do not charge

you for this guarantee.

• Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectication of

these defects or replacement of the device. Please note that our devices have not been designed for use in commercial, trade

or industrial applications. Consequently, the guarantee is invalidated if the equipment is used in commercial, trade or industrial

applications or for other equivalent activities. The following are also excluded from our guarantee: compensation for transport

damage, damage caused by failure to comply with the installation/assembly instructions or damage caused by unprofessional

installation, failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or current type), mis-

use or inappropriate use (such as overloading of the device or use of non-approved tools or accessories), failure to comply with

the maintenance and safety regulations, ingress of foreign bodies into the device (e.g. sand, stones or dust), effects of force or

external inuences (e.g. damage caused by the device being dropped) and normal wear resulting from proper operation of the

device.

The guarantee is rendered null and void if any attempt is made to tamper with the device.

• The guarantee is valid for a period of 3 years starting from the purchase date of the device. Guarantee claims should be

submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be

accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs

are carried out or parts are replaced. In such cases, the work performed or parts tted will not result in an extension of the

guarantee period, and no new guarantee will become active for the work performed or parts tted. This also applies when an

on-site service is used.

• In order to assert your guarantee claim, please send your defective device postage-free to the address shown below. Please

enclose either the original or a copy of your sales receipt or another dated proof of purchase. Please keep your sales receipt in

a safe place, as it is your proof of purchase. It would help us if you could describe the nature of the problem in as much detail

as possible. If the defect is covered by our guarantee then your device will either be repaired immediately and returned to you,

or we will send you a new device.

Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the scope of this guar-

antee or for units which are no longer covered. To take advantage of this service, please send the device to our service address.

16. Troubleshooting

Problem Possible Cause Help

Saw blade gets loose

after turning off the

motor

Fastening nut tightened insufciently Tighten fastening nut, M20 left-handed thread

Motor does not start a) Fastening nut tightened insufciently

b) Extension cable defect

c) Connections on the motor or switch defect

a) Check the mains fuse.

b) See “Electrical Connection” in the operating

manual

c) Have it checked by an electrician

No motor output turns

off automatically

Overload by dull saw blade, thermoprotection

is triggered

Insert a sharpened saw blade; motor can be turned

on again after the cooling period

Burns on the cutting

surface

c) with longitudinal cuts

d) with cross cuts

a) Fastening nut tightened insufciently

b) Wrong saw blade

c) Longitudinal stop not parallel

d) Slide carriage not parallel

a) Insert a sharpened saw blade

b) Insert saw blade with 20 or 28 teeth for

longitudinal cuts

c) Exchange the longitudinal stop

Align the slide carriage with the saw blade

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PTK 2000 A1 - IAN 104416 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info