Bedienungsanleitung Parkside PTK 2000 D3 - IAN 298657 (Seite 26 von 108) (Deutsch, Englisch, Holländisch, Portugiesisch, Spanisch)

691162

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

GB IE



the product.

Important Instructions

If the motor is overloaded, it switches itself off automatically.

After cooling down (times vary), the motor can be switched on

again.

Faulty Electrical Connection Cable

Insulation damage often occurs to electrical connection cables.

The causes of this may be as follows:

• Pressure points if connection cables are routed through

windows or door gaps.

• Kinks caused by improper attachment or routing of the

connection cable.

• Cut surfaces caused by vehicles driving over the connection

cable.

• Insulation damage caused by tearing out of the wall socket.

• Cracks resulting from the insulation becoming old.

Such faulty electrical connections must not be used and may

endanger life due to the damage to the insulation.

Electrical connection cables should be checked regularly for

damage. Ensure that during such checks, the connection cable is

not connected to the mains.

Electrical connection cables must comply with the relevant VDE

and DIN regulations. Only use connection cables with the mar-

king H05VV-F.

It is stipulated by law that the type of connection cable must be

printed on it.

Alternating Current Motor

• The mains voltage must be 230 V~.

• Extension cables up to 25 m in length must have a cross-sec-

tion of 2.5 mm².

Connections and repairs to the electrical equipment may only be



please provide the following information:

• Current type of the engine

• Data from the machine type plate

• Data from the motor type plate

Assembly

 

 

Assembly, Replacement of Parts and Adjustments

Caution! The mains plug must be removed before all

servicing, retooling and assembly work.



the parts which are similar.

Note: If connections are secured with a bolt (round head/or

hexagonal), hexagonal nuts and a washer, the washer must be

placed under the nut.

Insert the bolts from the outside to the inside in each case, secu-

ring the connections with nuts from the inside.

Note: Tighten the nuts and bolts during assembly only to the

extent that they cannot fall off.





Assembling the frame and table width

extender with length extender

(Figures. 4-13)

 

2. Insert the four legs (21) at the corner positions into the device

housing. Do not place any screws yet.

3. Now loosely screw the central struts (22) onto the legs (21).

Use the carriage bolts (b), the washers (c), the spring was-

hers (d) and the nuts (e) (Fig. 7).

4. Screw the stand brackets (21) into the rear legs using the

drill holes. Assembly material for each: 2 carriage bolts (b),

the washers (c), the spring washers (d) and the nuts (e)

(Fig. 9). Caution! Both stand brackets must be

attached to the rear of the machine at attachment

points 25! (Abb. 5).

5. Loosely tighten the table width extender (7) and table length

extender (17) on the saw table (1) using the hexagon bolts

with Phillips head (f). (Fig. 11). The ‘Parkside’ logo on the

table extensions (7) points away from the saw table (1).

6. Loosely tighten the table supports (26, 27) on the housing of

the table circular saw. Use the hexagonal bolts with collar

(a) from bag A. Use the table width extender (7)/table

length extender (17), hexagonal bolts (f), washers (c) and

nuts (e) from bag B. The short supports (26) are for the table

widening extension, the long supports (27) are for the length

extension, (Fig. 12, 13). Screw the four legs (21) and

the table supports (26, 27) onto the housing.

7. 

table.

8. Next, tighten all the screws of the legs (21) and the table

width extender (7)/table length extender (17).

9. Now attach the rubber feet (23) to the legs (21) (Figure 8).

10. Place the table circular saw on the base frame (13).

11. Screw one nut on each of the screws (g). Screw the four

screws with pre-mounted nuts onto the side of the table width



these with four additional nuts. Suspend the collection bag

for wood residues (15) onto the four screws.

Mounting / adjusting the Riving Knife

Insert the battery (Figures 15-20)

Caution! Remove the mains plug! The setting of the

saw blade (4) must be checked whenever a blade has

been replaced.

1. Inserting the batteries (Figure 15):

- Turn the laser on/off switch (36) to the 0 position (laser off).

- Remove the battery compartment cover (38) by loosening the

screw (37). Now remove the battery compartment cover (38)

by bending at the side.

- Insert the batteries supplied (type AAA), ensuring the correct

polarity (see Figure 15).

- Put the battery compartment cover (38) back in position and

tighten it with the screw (37). Notes concerning the batteries:

- If you are not going to use the laser for a prolonged period,

please remove the batteries from the battery compartment.

Parkside PTK 2000 D3 - IAN 298657 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info