Bedienungsanleitung Parkside PTK 2000 D3 - IAN 298657 (Seite 28 von 108) (Deutsch, Englisch, Holländisch, Portugiesisch, Spanisch)

691162

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

GB IE

Operation

Switching on and off

(Figure 3)

- The saw can be switched on by pressing the green pushbut-

ton „I“. Before you start sawing, wait until the saw blade has

reached its maximum speed.

- In order to switch the saw off again, the red pushbutton „0“

has to be pressed.

Adjusting the Cutting Depth

(Figure 3)

By turning the crank handle (12), the saw blade can be set to the

desired cutting depth (continuous).

- Clockwise: increases the cutting depth

- Anticlockwise: reduces the cutting depth

Adjust the saw blade so that it protrudes approximately 5

mm above the material to be cut. Check the adjustment by

means of a test cut.

Working with the Parallel Stop

Adjusting the Stop Height

(Figures 22 and 24)

- The stop rail (39) of the parallel stop (6) has two guide

surfaces at different heights.

- Depending on the thickness of the materials to be cut, the

stop rail (39) has to be used differently. For thin material

(workpiece thickness less than 25 mm), use Figure 22. For

thick material (workpiece thickness more than 25 mm), use

Figure 24.

Turning the Stop Rail

(Figures 22-24)

 

nuts (m).

- Now the stop rail (39) can be pulled off the guide rail (16)

and pushed back over it again with the groove.

- Tighten the knurled nuts (m) again.

Adjusting the Cutting Width

(Figures 25-26)

- When wooden pieces are being cut lengthwise, the parallel

stop (6) has to be used.

- The parallel stop should be mounted on the right-hand side

of the saw blade (4).

- Insert the parallel stop into the side of the guide rail (16)

(Figure 26).

- On the guide rail for the parallel stop (6) there are 2 scales

(o/n). These show the distance between the stop rail (39)

and saw blade (4) (Figure 25).

- Select the suitable scale according to whether the stop rail

(39) has been turned around for working with thick or thin

material:

High stop rail (thick material): scale (o)

Low stop rail (thin material): scale (n)

- Adjust the parallel stop (6) to the desired level on the sight



Adjusting the Stop Length

(Figure 27)

- In order to prevent the material being cut from jamming, the

stop rail (39) can be moved in the longitudinal direction.

- Rule of thumb: the rear end of the stop abuts on an imagi-

nary line. This begins at about the middle of the saw blade

and runs towards the back at an angle of 45°.

- Adjust the required cutting width.

- Release the knurled nuts (m) and push the stop rail (39)

forward until the imaginary 45° line is touched.

- Tighten the knurled nuts (m) again.

Adjusting the Parallel Stop

(Figure 28)

- Caution! Remove the guard.

- Adjust the saw blade (4) to the maximum cutting depth.

- Adjust the parallel stop (6) such that the stop rail (39)

touches the saw blade (adjustment for thick material.

- If the parallel stop (6) is not parallel to the saw blade (4),

please proceed as follows. Release the screws (r) on the

parallel stop until the parallel stop (6) can be aligned to be

parallel with the saw blade (4) (Figure 28).

- Retighten the screws (r).

Transverse stop

(Figure 29)

- When the wood is being cut to size, the transverse stop (40)

must be extended with the stop rail (39) of the parallel stop

(6) (Figure 29)

- Push the transverse stop (40) into a groove (33) of the saw

table.

- Loosen the knurled screw (34).

- Turn the transverse stop (40) until the desired angle is set.

The notch on the guide bar shows the angle that has been

set.

- Retighten the knurled screw (34).

- In order to extend the transverse stop (40) with the stop rail

(39), the stop rail (39) has to be removed from the parallel

stop (6). Now the stop rail has to be mounted as shown in

Figure 29; use the knurled nuts (m) for this purpose.

Caution!

- Do not push the stop rail (39) too far in the direction of the

saw blade.

- The distance between the stop rail (39) and saw blade (4)

should be approximately 2 cm.

Adjusting the scale of the parallel stop

(Figure 30)

- Check whether the display on the sight glass (p) of the

parallel stop (6) shows the correct values with respect to the

cutting line. If this is not the case, please proceed as follows:

- Release the screw (q) with which the display on the sight

glass (p) of the parallel stop (6) is attached. The sight glass

(p) display can now be set to the correct position.

- Now, retighten screw (q) on the sight glass (p).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PTK 2000 D3 - IAN 298657 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info