Bedienungsanleitung Parkside PZKS 1500 A1 - IAN 273098 (Seite 12 von 64) (Deutsch, Englisch, Holländisch, Französisch)

706378

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

7GB/IE

• Never open the laser module. Unexpected exposure

to the beam can occur.

• If the mitre saw is not used for an extended period

of time, the batteries should be removed.

• The laser may not be replaced with a different type

of laser.

• Repairs of the laser may only be carried out by the

laser manufacturer or an authorised representative.

Safety instructions for handling batteries

1 Always make sure that the batteries are inserted

with the correct polarity (+ and –), as indicated on

the battery.

2 Do not short-circuit batteries.

3 Do not charge non-rechargeable batteries.

4 Do not overcharge batteries!

5 Do not mix old and new batteries or batteries of

different types or manufacturers! Replace an entire

set of batteries at the same time.

6 Immediately remove used batteries from the de-

vice and dispose of them properly! Do not dispose

batteries with household waste. Defective or used

batteries must be recycled according to Directive

2006/66 / EC. Give back batteries and / or the device

has been offered to the collective facilities. About

disposal facilities you can inform by your municipal

or city government.

7 Do not allow batteries to heat up!

8 Do not weld or solder directly on batteries!

9 Do not dismantle batteries!

10 Do not allow batteries to deform!

11 'RQRWWKURZEDWWHULHVLQWR¿UH

12 Keep batteries out of the reach of children.

13 Do not allow children to replace batteries without

supervision!

14 'R QRW NHHS EDWWHULHV QHDU ¿UH RYHQV RU RWKHU

sources of heat. Do not use batteries in direct sun-

light or store them in vehicles in hot weather.

15 Keep unused batteries in the original packaging and

keep them away from metal objects. Do not mix

unpacked batteries or toss them together! This can

lead to a short-circuit of the battery and thus dam-

DJHEXUQVRUHYHQWKHULVNRI¿UH

16 Remove batteries from the equipment when it will

not be used for an extended period of time, unless

it is for emergencies!

17 NEVER handle batteries that have leaked without

DSSURSULDWHSURWHFWLRQ,IWKHOHDNHGÀXLGFRPHVLQWR

contact with your skin, the skin in this area should be

rinsed off under running water immediately. Always

SUHYHQWWKHÀXLGIURPFRPLQJLQWRFRQWDFWZLWKWKH

eyes and mouth. In the event of contact, please seek

immediate medical attention.

18 Clean the battery contacts and corresponding con-

tacts in the device prior to inserting the batteries:

6. Technical data

AC motor 220 - 240 V ~ 50Hz

Power 1200 Watt

Operating mode S6 25%* 1500W

Idle speed n

5000 min

-1

Carbide saw blade ø 210 x ø 30 x 2,6 mm

Number of teeth 24

Swivel range -45° / 0°/ +45°

Mitre cut 0° bis 45° nach links

Saw width at 90° 340 x 58 mm

Saw width at 45° 240 x 58 mm

Saw width at 2 x 45°

(double mitre cut)

240 x 32 mm

Protection class II

Weight approx. 17 kg

Laser class 2

Wavelength of laser 650 nm

Laser output < 1 mW

Laser module power

supply

2 x 1,5 V Micro (AAA)

* S6, continuous operation periodic duty.

Identical duty cycles with a period at load followed

by a period at no load. Running time 10 minutes;

duty cycle is 25% of the running time.

The work piece must have a minimum height of 3mm

and a minimum width of 10 mm.

Make sure that the workpiece is always secured with

the clamping device.

Noise

Total noise values determined in accordance with EN

61029.

sound pressure level L

99.6 dB(A)

uncertainty K

3 dB

sound power level L

112.6 dB(A)

uncertainty K

3 dB

Wear hearing protection.

The effects of noise can cause a loss of hearing.

Residual risks

The machine has been built according to the state of

the art and the recognised technical safety require-

ments. However, individual residual risks can arise

during operation.

• Health hazard due to electrical power, with the use of

improper electrical connection cables.

• Furthermore, despite all precautions having been met,

some non-obvious residual risks may still remain.

• Residual risks can be minimised if the „safety instruc-

tions“ and the „Proper use“ are observed along with

the whole of the operating instructions.

• Do not load the machine unnecessarily: excessive

pressure when sawing will quickly damage the saw

blade, which results in reduced output of the machine

in the processing and in cut precision.

• When cutting plastic material, please always use

clamps: the parts which should be cut must always

EH¿[HGEHWZHHQWKHFODPSV

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PZKS 1500 A1 - IAN 273098 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info