Bedienungsanleitung Parkside PZKS 1500 B2 - IAN 280657 (Seite 98 von 106) (Deutsch, Englisch, Holländisch, Französisch)

706372

Zoom out

Zoom in

Vorherige Seite

1/106

Nächste Seite

93GB / IE / NI

- Attach the miter lock handle (10) to the

turntable (15).

- When fixing the saw to the workbench,

insert the mounting screws (not included)

through the mounting holes (16a).

•Inordertoadjusttheturntable(15)

loosen the mitre lock handle (10) approx.

2 turns.

•Pressthemitredetentlever(11)andturn

the turntable (15) and pointer (12) to the

desired angle measurement on the scale

(14), release the mitre detent lever (11)

and secure with the mitre lock handle

(10).

•Pressingthemachinehead(4)lightly

downwards and removing the fastening

bolt (30) from the motor bracket at the

same time disengages the saw from the

lowest position.

•Swingthemachinehead(4)upuntilthe

release lever (3) latches into place.

•Itispossibletosecuretheclamping

device (7) to the left or right on the

stationary saw bench. Insert the clamping

device (7) in the hole on the rear side of

the stop rail (17) and secure it with the

grip screw (28).

•Attachtheworkpiecesupports(8)tothe

fixed saw table (16) as shown in Figure

5 and fasten with the screw (29).

•Itispossibletotiltthemachinehead(4)

a max. 45° to the left by loosening the

locking screw (27).

8.2 Mitre angle setting

•Ninepositivemiterdetentsareprovided

for fast and accurate preset miter angles

– locations are at 45°, 30°, 22.5°, 15°

left and right, and center at 0°.

•Followtheprocessformitreanglesetting.

•Unlocktheturntablebyturningthemitre

lock handle (10) counter-clockwise.

•Movetheturntablewhilepressthemitre

detent lever (11) to align the mitre angle

pointer (12) to the desired degree on the

mitre angle scale (14).

•Ifthedesiredangleisoneofthenine

positive mitre detents, release the mitre

detent lever (11), making sure the lever

snaps into position, and then secure by

tightening the mitre lock handle (10).

•Ifthemitreangledesiredisnotoneofthe

nine positive mitre detents, simply lock

the turntable into desired angle position

by turning the mitre lock handle (10) in

the clockwise direction.

8.3 Precision adjustment of the

blade for crosscut 90°

(Fig. 1/2/6/7)

• Nostopangleincluded.

• Movethehead(4)inposition,sothat

the blade (6) rests directly above the

turntable (15). Now, use locking screw

(25) to lock the drag guide (26).

• Lowerthemachinehead(4)andsecure

using the fastening bolt (30).

•Loosenthebevellockingscrew(27).

•Positiontheanglestop(a)betweenthe

saw blade (6) and the turntable (15).

•Releasethelockingnut(c)andadjust

the adjusting screw (32) until the angle

between the saw blade (6) and turntable

(15) is 90°.

•Re-tightenthelockingnut(c).

•Subsequentlycheckthepositionofthe

angle indicator. If necessary loosen the

pointer (24) using a Philips screwdriver,

set to position 0° on the angle scale (23)

and re-tighten the retaining screw.

8.4 Precision adjustment of stop

rail for crosscut 90°

(Fig. 1/8/9)

- Bring the power tool into the working

position.

- Turn the turntable (15) to the 0° on the

mitre angle scale (14). The metre detent

lever

（

）

must be felt to engage in

the detent.

Attachment and operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PZKS 1500 B2 - IAN 280657 Seite 98

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info