Bedienungsanleitung Parkside PZKS 1500 B2 - IAN 280657 (Seite 102 von 106) (Deutsch, Englisch, Holländisch, Französisch)

706372

102

Zoom out

Zoom in

Vorherige Seite

1/106

Nächste Seite

97GB / IE / NI

• Tightenthecoverplatescrewwiththe

4 mm Allen key (e).

• Beforecontinuingyourwork,make

sure that all safety devices are in good

working condition.

•

Important!

Every time that you change

the saw blade (6), check to see that it

spins freely in the table insert (9) in both

perpendicular and 45° angle settings.

•

Important!

The work to change and

align the saw blade (6) must be carried

out correctly.

8.13 Using the laser (Fig. 2/21)

• Toswitchon:MovetheON/OFFswitch

of the laser (31) to the “I” position. A

laser line is projected onto the material

you wish to process, providing an exact

guide for the cut.

• Toswitchoff:MovetheON/OFFswitch

of the laser (31) to the “0” position.

8.14 Adjusting the laser (Fig. 21)

WARNING! While adjusting the laser

(e. g. when moving the tool arm),

never actuate the ON/OFF switch (2).

Accidentally starting the power tool can

lead to injuries.

If the laser (13) ceases to indicate the correct

cutting line, you can readjust the laser. To do

so, open the screws (39) and set the laser

by moving sideways to that the laser beam

strikes the teeth of the saw blade (6).

9. Transport

•Tightenmitrelockhandle(10)inorderto

lock the turntable (15)

•Activatethereleaselever(3),press

the machine head (4) downwards and

secure with the fastening bolt (30). The

saw is now locked in its bottom position.

•Fixthesaw’sdragfunctionwiththe

locking screw for drag guide (25) in rear

position.

•Carrythemachinebythetransport

carrying handle or hold it by the

recessed handles on the sides of the saw

table.

•Whenreassemblingtheequipment

proceed as described under section 7.

10. Maintenance

Warning! Prior to any adjustment,

maintenance or service work disconnect the

mains power plug!

General maintenance measures

Cleaning

For safe and proper working, always keep

the power tool and its ventilation slots clean.

The retracting blade guard must always be

able to move freely and retract automatically.

Therefore, always keep the area around the

retracting blade guard clean.

Remove dust and chips after each working

procedure by blowing out with compressed

air or with a brush.

Clean the guard roller, automatic extension

fence and turntable regularly.

To clean the laser unit and remove any dust

using a brush.

When cleaning the plastic do not use

corrosive products.

Carbon brush inspection

Check the carbon brushes after the first 50

operating hours with a new machine, or

when new brushes have been fitted. After

carrying out the first check, repeat the check

every 10 operating hours.

If the carbon is worn to a length of 6 mm,

Transport/Maintenance

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PZKS 1500 B2 - IAN 280657 Seite 102

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info