Bedienungsanleitung Parkside PZKS 1500 B2 - IAN 295934 (Seite 105 von 110) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

706364

105

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

100

GB / IE / NI

coatings, some wood types, minerals and

metal can be harmful to one’s health.

Touching or breathing-in the dust can cause

allergic reactions and/or lead to respiratory

infections of the user or bystanders.

Certain dust, such as oak or beech dust,

is considered carcinogenic, especially in

connection with wood-treatment additives

(chromate, wood preservative). Materials

containing asbestos may only be worked by

specialists.

- Always use dust extraction.

- Provide for good ventilation of the

working place.

- It is recommended to wear a P2 filter-

class respirator.

Observe the relevant regulations in your

country for the materials to be worked.

Prevent dust accumulation at the

workplace.

Dust can easily ignite.

The dust/chip extraction can be blocked by

dust, chips or workpiece fragments.

- Switch the machine off and pull the mains

plug from the socket outlet.

- Wait until the saw blade has come to a

complete stop.

- Determine the cause of the blockage and

correct it.

External Dust Extraction

For dust extraction, a vacuum hose (size

Ø 35 mm) can also be connected to the dust

extraction spout.

- Connect the vacuum hose with the dust

extraction spout .

The vacuum cleaner must be suitable for

the material being worked.

When vacuuming dry dust that is

especially detrimental to health or

carcinogenic, use a special vacuum

cleaner.

The saw is equipped with a sawdust bag (21)

for sawdust and chips.

Squeeze together the metal ring on the dust

bag and attach it to the outlet opening in the

motor area.

The sawdust bag (21) can be emptied by

means of a zipper at the bottom.

8.12 Changing the saw blade

(Fig. 1/17/18/19/20)

• Allow the machine head (4) to rise to the

upright position.

• Loosen the cover plate screw with the

4 mm Allen key (e).

WARNING!

Do not remove this screw.

• Hold the release lever (3) to the right.

Then, rotate the cover plate (20) upward

and raise the movable blade guard to

the upper position to expose the flange

bolt (35). Let the release lever (3) move

back to its default position.

• Place the 6 mm Allen key (d) over the

flange bolt.

• Press the saw shaft lock (37), holding

it in firmly while turning the 6mm Allen

key (d) clockwise. The shaft lock will be

engage after turning the 6mm Allen key.

• Continue to hold the saw shaft lock to

keep it engaged, while turning the blade

Allen key clockwise to loosen the flange

bolt (35).

• Remove the flange bolt (35) and the

outer flange (36).

• Take the saw blade (6) off the inner

flange (38) and pull out downwards.

NOTE:

Pay attention to the pieces

removed, noting their position and

direction they face.

• Carefully clean the flange bolt (35), outer

flange (36) and inner flange (38).

• Fit and fasten the new saw blade (6) in

reverse order.

•

Important!

The cutting angle of the teeth,

in other words the direction of rotation of

the saw blade (6) must coincide with the

direction of the arrow on the housing.

• Hold the release lever (3) to the right.

Rotate the cover plate (20) downward

Attachment and operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PZKS 1500 B2 - IAN 295934 Seite 105

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info