Bedienungsanleitung Parkside PZKS 1500 B2 - IAN 295934 (Seite 103 von 110) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

706364

103

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

GB / IE / NI

Checking:

(see figure 9)

- Adjust an angle gauge to 90° and

position it between the stop rail (17) and

the saw blade (6) on the turntable (15).

The leg of the angle gauge must be flush

with the saw blade (6) over the complete

length.

Adjusting:

(see figure 8/9)

- Loosen all four set screws (33) and turn

the stop rail (17) until the leg of the angle

gauge is flush with the stop rail over the

complete length.

- Retighten the four set screws again.

When the mitre angle pointer (12) is not

in line with the 0° mark of mitre angle

scale (14) after adjusting, loosen the

screw on the mitre angle pointer (12)

with a philips screwdriver and align the

angle pointer pointed to the 0°mark.

8.5 Cross cut 90° and turntable 0°

(Fig. 10/12)

In the case of cutting widths up to approx.

100 mm it is possible to fix the traction

function of the saw with the locking screw

(25) in the rear position. In this position the

machine can be operated in cross cutting

mode. If the cutting width is over 100 mm

then it is necessary to ensure that the locking

screw (25) is loose and the machine head (4)

can move.

• Move the machine head (4) to its upper

position.

• Use the handle (1) to push back the

machine head (4) and fix it in this

position if required(dependent on the

cutting width).

• Place the piece of wood to be cut at the

stop rail (17) and on the turntable (15).

• Lock the material with the clamping

device (7) on the fixed saw table(16) to

prevent the material from moving during

the cutting operation.

• Operate the release lever (3) to release

the machine head (4).

• Press the ON/OFF switch (2) to start the

motor.

• With the drag guide (26) fixed in place:

Use the handle (1) to move the machine

head (4) steadily and with light pressure

downwards until the saw blade (6) has

completely cut through the work piece.

• With the drag guide (26) not fixed in

place:

Pull the machine head (4) all the way

to the front. Lower the handle (1) to the

very bottom by applying steady and

light downward pressure. Now push the

machine head (4) slowly and steadily to

the very back until the saw blade (6) has

completely cut through the work piece.

• When the cutting operation is completed,

move the machine head (4) back to its

upper (home) position and release the

ON/OFF switch (2).

Attention! The machine executes an upward

stroke automatically due to the return

spring, i.e. do not release the handle (1)

after completing the cut; instead allow the

machine head to move upwards slowly

whilst applying light counter pressure.

8.6 Cross cut 90° and metre cut 0°

- 45° (Fig. 10/11)

The crosscut saw can be used to make

crosscuts of 0° -45° to the left and 0° - 45° to

the right in relation to the stop rail.

• Loosen the metre lock handle (10) in case

it is tightened, press the metre detent

lever (11) and use the mitre lock handle

(10) to adjust the turntable (15) to the

desired angle. The mitre angle pointer

(12) on the turntable must match the

desired angle on the mitre angle scale

(14) on the fixed saw table (16).

• Re-tighten the mitre lock handle (10) in

order to secure the turntable (15).

Attachment and operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PZKS 1500 B2 - IAN 295934 Seite 103

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info