Bedienungsanleitung Parkside PZKS 1500 B2 - IAN 295934 (Seite 101 von 110) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

706364

101

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

GB / IE / NI

Safety measures must be defined to protect

the operator. They must be based on an

assessment of exposure during actual usage

conditions (all parts of the operating

cycle must be accounted for, e.g. periods

when the power tool is switched off and

when it is switched on, but not operating

under load).

Reduce the vibration risk by

- wearing protective gloves during use and

- limiting the working time and reducing

the actual operation time.

Residual risks

The machine has been built according to

the state of the art and the recognised

technical safety requirements.However,

individual residual risks can arise during

operation.

• Health hazard due to electrical power,

with the use of improper electrical

connection cables.

• Furthermore, despite all precautions

having been met, some non-obvious

residual risks may still remain.

• Residual risks can be minimised if the

"Safety information" and the "Intended

use" are observed along with the whole

of the operating instructions.

• Do not load the machine unnecessarily:

excessive pressure when sawing will

quickly damage the saw blade, which

results in reduced output of the machine

in the processing and in cut precision.

• When cutting plastic material, please

always use clamps: the parts which

should be cut must always be fixed

between the clamps.

• Avoid accidental starting of the machine:

the operating button may not be pressed

when inserting the plug in an outlet.

• Use the tool that is recommended in this

manual. In doing so, your mitre saw

provides optimal performance.

• Hands may never enter the processing

zone when the machine is in operation.

Release the handle button and switch off

the machine prior to any operations.

7. Before starting the

equipment

• The equipment must be set up where it

can stand securely. Secure the machine

on a workbench or a stand with 4 screws

through the holes in the fixed saw table

(16).

• All covers and safety devices have to be

properly fitted before the equipment is

switched on.

• It must be possible for the blade to run

freely.

• When working with wood that has been

processed before, watch out for foreign

bodies such as nails or screws, etc.

• Before you press the ON/OFF switch

check that the saw blade is fitted

correctly. Moving parts must run

smoothly.

• Before you connect the equipment to the

power supply make sure the data on the

rating plate are dentical to the mains

data.

8. Attachment and operation

8.1 Attaching the saw

(Fig1/2/3/4/5)

WARNING! Avoid unintentional starting

of the machine. During assembly and

for all work on the machine, the power

plug must not be connected to the mains

supply.

- Attach the carry handle (22) to the

machine head (4) with 2 x screws.

Before starting the equipment/Attachment and operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PZKS 1500 B2 - IAN 295934 Seite 101

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info