706364
102
Zoom out
Zoom in
Vorherige Seite
1/110
Nächste Seite
97GB / IE / NI
- Attach the miter lock handle (10) to the
turntable (15).
- When fixing the saw to the workbench,
insert the mounting screws (not included)
through the mounting holes (16a).
• In order to adjust the turntable (15)
loosen the mitre lock handle (10) approx.
2 turns.
• Press the mitre detent lever (11) and turn
the turntable (15) and pointer (12) to the
desired angle measurement on the scale
(14), release the mitre detent lever (11)
and secure with the mitre lock handle
(10).
• Pressing the machine head (4) lightly
downwards and removing the fastening
bolt (30) from the motor bracket at the
same time disengages the saw from the
lowest position.
• Swing the machine head (4) up until the
release lever (3) latches into place.
• It is possible to secure the clamping
device (7) to the left or right on the
stationary saw bench. Insert the clamping
device (7) in the hole on the rear side of
the stop rail (17) and secure it with the
grip screw (28).
• Attach the workpiece supports (8) to the
fixed saw table (16) as shown in Figure
5 and fasten with the screw (29).
• It is possible to tilt the machine head (4)
a max. 45° to the left by loosening the
locking screw (27).
8.2 Mitre angle setting
• Nine positive miter detents are provided
for fast and accurate preset miter angles
– locations are at 45°, 30°, 22.5°, 15°
left and right, and center at 0°.
• Follow the process for mitre angle setting.
• Unlock the turntable by turning the mitre
lock handle (10) counter-clockwise.
• Move the turntable while press the mitre
detent lever (11) to align the mitre angle
pointer (12) to the desired degree on the
mitre angle scale (14).
• If the desired angle is one of the nine
positive mitre detents, release the mitre
detent lever (11), making sure the lever
snaps into position, and then secure by
tightening the mitre lock handle (10).
• If the mitre angle desired is not one of the
nine positive mitre detents, simply lock
the turntable into desired angle position
by turning the mitre lock handle (10) in
the clockwise direction.
8.3 Precision adjustment of the
blade for crosscut 90°
(Fig. 1/2/6/7)
No stop angle included.
Move the head (4) in position, so that
the blade (6) rests directly above the
turntable (15). Now, use locking screw
(25) to lock the drag guide (26).
Lower the machine head (4) and secure
using the fastening bolt (30).
• Loosen the bevel locking screw (27).
• Position the angle stop (a) between the
saw blade (6) and the turntable (15).
• Release the locking nut (c) and adjust
the adjusting screw (32) until the angle
between the saw blade (6) and turntable
(15) is 90°.
• Re-tighten the locking nut (c).
• Subsequently check the position of the
angle indicator. If necessary loosen the
pointer (24) using a Philips screwdriver,
set to position 0° on the angle scale (23)
and re-tighten the retaining screw.
8.4 Precision adjustment of stop
rail for crosscut 90°
(Fig. 1/8/9)
- Bring the power tool into the working
position.
- Turn the turntable (15) to the 0° on the
mitre angle scale (14). The metre detent
lever
11
must be felt to engage in
the detent.
Attachment and operation
102

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PZKS 1500 B2 - IAN 295934 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info