Bedienungsanleitung Partner P33XT (Seite 7 von 15) (Deutsch, Englisch, Französisch, Spanisch)

518732

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

ATTACHING THE BAR & CHAIN

(If not already attached)

WARNING: Recheck each assem-

bly step if the saw is received assembled.Al-

ways wear gloves when handling the chain.

The chain is sharp and can cut you even

when it is not moving!

1. Loosen and remove thechain brake nuts

and the chain brake from the saw .

2. Remove the plastic shipping spacer (if

present).

Chain

Brake

Chain Brake

Nuts

Clutch Drum

3. An adjusting pin and screw is used to ad-

just the tension of the chain. It is very im-

portant when assembling the bar , that the

pin located on the adjusting screw aligns

into a hole in the bar . Tu rning the screw will

move the adjustment pin up and down the

screw. Locate this adjustment before you

begin mounting the bar onto the saw. See

illustration below .

Adjustment located on Chain Brake

Inside view of

Chain Brake

4. Turn the adjusting screw by hand coun-

terclockwise until the adjusting pin just

touches the stop. This should allow the

pin to be near the correct position.

5. Slide guide bar behind clutch drum until

guide bar stops against clutch drum

spro cke t .

Mount the Bar

6. Carefully remove the chain from the pack-

age. Hold chain with the drive links as

sho wn .

CUTTERS MUST F ACE IN

DIIRECTION OF ROTATION

Tip of

Bar

Cutters

Depth Gauge

Drive Links

Placechainontothes

rocket

7. Place chain over and behind clutch, fitting

the drive links in the clutch drum sprocket.

8. Fit bottom of drive links between the

teeth in the sprocket in the nose of the

guide bar.

9. Fit chain drive links into bar groove.

10. Pull guide bar forward until chain is snug

in guide bar groove. Ensure all drive

links are in the bar groove.

11. Now, install chain brake making sure the

adjusting pin is positioned in the lower

hole in the guide bar . Remember this pin

moves the bar forward and backward as

the screw is turned.

12. Installchainbrake nuts andfingertighten

only. Once the chain is tensioned, you

will need to tighten chain brake nuts.

CHAIN TENSION (Including units

with chain already installed)

NOTE

: When adjusting chain tension, make

sure the chain brake nuts are finger tight only .

Attempting to tension the chain when the chain

brake nuts are tight can cause damage.

Checking the tension:

Use the screwdriver end of the chain adjust-

ment tool (bar tool) to move the chain around

the bar. If the chain does not rotate, it is too

tight. If too loose, the chain will sag below the

bar .

Chain Brake Nuts

Chain Adjustment

Tool (Bar Tool)

Adjusting the tension:

Chain tension is very important. Chain

stretches during use. This is especially true

during the first few times you use your saw.

Always check chain tension each time you

use and refuel your saw . You can adjust the

chain tension by loosening the chain brake

nuts and turning the adjusting screw 1/4 of a

turn while lifting up on the bar.

S Ifchainistoo tight, turnadjusting screw 1/4

turn counterclockwise.

S If chain is too loose, turn adjusting screw

1/4 turn clockwise.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Partner P33XT Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info