Bedienungsanleitung Partner P340S (Seite 6 von 282) (Deutsch, Englisch, Dänisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

518739

Zoom out

Zoom in

Vorherige Seite

1/282

Nächste Seite

-- 5 --

WARNING:

Kickback can lead to

dangerous loss of control of the chain saw

and result in serious or fatal injury to the

saw operator or to anyone standing close

by. Always be alert. Rotational kickback

and pinch-kickback are major chain saw

operational dangers and the leading cause

of most accidents.

Your Chain Saw is provided with a safety

label located on the chain brake lever/hand

guard. This label, along with the safety

instructions on these pages, should be

carefully read before attempting to operate

this unit.

IMPORTANT SAFETY

ASSEMBLY INSTRUCTIONS

WARNING: RED Used to warn that

an unsafe procedure should not be

performed.

WARNING: DO NOT start saw

engine until unit is properly prepared.

WARNING: Always wear protective

gloves when handling chain.

HOW TO READ SYMBOLS AND

COLORS (FIG.1)

WARNING

1. Beware of kickback.

2. Do not attempt to hold saw with one

hand.

3. Avoid bar nose contact.

RECOMMENDED

4. Hold saw properly with both hands.

You will need these tools to assemble your

chain saw:

1. Combination wrench-screwdriver (cont-

ained in your user’s kit).

2. Heavy duty work gloves (user supplied).

TO INSTALL GUIDE BAR:

To ensure the bar and chain receive oil,

ONLY USE THE ORIGINAL STYLE BAR

with the oil passage hole (A) as illustrated

above. (Fig.3A)

1. Make sure the CHAIN BRAKE lever is

pulled back into the DISENGAGED

position (Fig. 3B)

2. Remove the bar retaining nut

(B). Remove the CHAIN BRAKE cover

may be required. (Fig.3C).

Note: Discard the two plastic washers.They

are only used for shipping the chain saw.

3. Using a screwdriver, turn the adjustm-

ent screw (D) COUNTERCLOCKWISE

until the TANG (E) (projecting prong) is to

the end of its travel (Fig. 3D).

4. Place the slotted end of the guide bar

over the bar bolt (F). Slide guide bar

behind clutch drum

(G) until the

guide

bar stops (Fig.3E).

Your new chain saw will require adjustment

of chain, filling the fuel tank with correct fuel

mixture and filling the oil tank with lubricating

oil before the unit is ready for operation.

Read the entire user manual before

attempting to operate your unit. Pay

particular attention to all safety

precautions.

Your user manual is both a reference guide

and handbook provided to furnish you

with general information to assemble,

operate and maintain your saw.

GREEN RECOMMENDED

Recommended cutting procedure.

1 2

3 4

Fig. 1

DANGER! BEWARE OF KICKBACK!

Fig. 2A

Fig. 2B

BEWARE OF:

ROTATIONAL

KICKBACK

(Fig. 2A)

A = Kickback path

B = Kickback

reaction zone

THE PUSH (PINCH

KICKBACK) AND

PULL REACTIONS

(Fig. 2B)

A = Pull

B = Solid objects

C = Push

TOOLS FOR ASSEMBLY

ASSEMBLY REQUIREMENTS

GUIDE BAR / SAW CHAIN / CLUTCH

COVER INSTALLATION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Partner P340S Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info