Bedienungsanleitung Partner P340S (Seite 7 von 282) (Deutsch, Englisch, Dänisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

518739

Zoom out

Zoom in

Vorherige Seite

1/282

Nächste Seite

-- 6 --

Proper tension of saw chain is extremely

important and must be checked before

starting, as well as during any cutting

operation.

WARNING: Always wear heavy duty

gloves when handling saw chain or making

saw chain adjustments.

CAUTION: A new saw chain

stretches, requiring adjustment after as

few as 5 cuts. This is normal with a new

chain, and the interval between future

adjustments will lengthen quickly.

CAUTION: If saw chain is TOO

LOOSE or TOO TIGHT, the sprocket, bar,

chain, and crankshaft bearings will wear

more rapidly. Study Fig. 6 for information

concerning correct cold tension (A),

correct warm tension (B), and as a guide for

when saw chain needs adjustment (C).

Always wear heavy duty gloves when

handling saw chain or making saw chain

adjustments.

1. Spread chain out in a loop with cutting

edges (A) pointing CLOCKWISE around

loop (Fig. 4A).

2. Slip the chain around the sprocket (B)

behind the clutch (C). Make sure the

links fit between the sprocket teeth

(Fig. 4B).

3. Guide the drive links into the groove (D)

and around the end of the bar (Fig. 4B).

NOTE: The saw chain may droop slightly on

the lower part of bar. This is normal.

4. Pull guide bar forward until chain is

snug. Ensure all drive links are in the bar

groove.

5. Install the clutch cover making sure the

tang is positioned in the lower hole in the

guide bar. Make sure the chain does not

slip off of the bar. Install the bar retaining

nut hand tight and follow tension

adjustment instructions in Section

SAW CHAIN TENSION

ADJUSTMENT.

NOTE: The guide bar retaining nuts are

installed only hand tight at this point

because saw chain

adjustment is

required. Follow instructions in Section

SAW CHAIN TENSION ADJUSTMENT.

1. Hold nose of guide bar up and turn

adjustment screw

(A) CLOCKWISE to

increase chain tension. Turning screw

COUNTERCLOCKWISE will decrease

amount of tension on chain. Ensure the

chain fits snugly all the way around the

guide bar (Fig. 5).

2. After making adjustment, and while still

holding nose of bar in the uppermost

position, tighten the bar retaining nuts

securely. Chain has proper tension

when it has a snug fit all around and

can be pulled around by gloved hand.

NOTE: If chain is difficult to rotate on

guide bar or if it binds, too much tension

has been applied. This requires minor

adjustment as follows:

A. Loosen the bar retaining nuts so they

are finger tight. Decrease tension by

turning the bar adjustment screw

COUNTERCLOCKWISE slowly. Move

chain back and forth on bar. Continue to

adjust until chain rotates freely, but fits

snugly. Increase tension by turning bar

adjustment screw CLOCKWISE.

B. When saw chain has proper tension,

hold nose of bar in the uppermost

position and tighten the 2 bar

retaining

nuts securely.

Fig. 3A

Fig. 3B

Fig. 3C

Fig. 3D

Fig. 3E

TO INSTALL SAW CHAIN:

SAW CHAIN TENSION ADJUSTMENT

Taking the time to make needed

adjustments to the saw chain will result in

improved cutting performance and

prolonged chain life.

TO ADJUST SAW CHAIN:

Fig. 4A

Fig. 4B

Fig. 5

Fig. 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Partner P340S Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info