Bedienungsanleitung Partner P340S (Seite 9 von 282) (Deutsch, Englisch, Dänisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

518739

Zoom out

Zoom in

Vorherige Seite

1/282

Nächste Seite

-- 8 --

1. Fill the fuel tank (A) with correct fuel

mixture. (Fig. 8).

2. Fill the oil tank (B) with correct chain and

bar oil (Fig. 8).

3. Be certain the chain brake is disengaged

1. Make sure the on/off switch is in the “I”

position.

2. Depress the primer bulb 10 times.

3. Pull the starter rope rapidly 4

times. The engine should start.

4. If the engine still can not start, follow the

step as “To start engine” in this user

manual.

1. Release trigger and allow engine to

return to idle speed.

2. Press STOP switch down to stop engine

Figure 9G.

NOTE: For emergency stopping, simply

activate CHAIN BRAKE and move

STOP switch down.

1. Place saw on a clear, firm, flat surface.

2. Start engine.

3. Grasp the rear handle (A) with your right

hand (Fig. 10).

4. With your left hand, hold the front

handle (B) [not CHAIN BRAKElever (C)]

firmly (Fig. 10).

5. Squeeze the throttle trigger to 1/3 throttle,

then immediately activate the

CHAIN

BRAKElever (C) (Fig. 10).

6. Chain should stop abruptly. When it does,

immediately release the throttle trigger.

7. If chain brake functions properly, turn the

engine off

and return the chain brake to

the DISENGAGED position.

Test the CHAIN BRAKE periodically to

ensure proper function.

Perform a CHAIN BRAKE test prior to initial

cutting, following extensive cutting, and

definitely following any CHAIN BRAKE

service.

1. Move ON/OFF switch to ON “I”

position. (Fig. 9A)

2. Pull choke lever/throttle (A) advance.This

sets choke and advances throttle for

easier starting. (Fig. 9B)

3. Press primer bulb (B) 10 times. (Fig. 9C)

4. With saw on ground, grip front handle

firmly with left hand and place right foot

inside rear handle. Pull starter rope 4

times with right hand. (Fig. 9D)

NOTE: If the engine sounds as if it wants

to start before the 4th pull, end the tugging

of the starter and proceed as described in

the next step.

5. Push choke lever (C) in

completely. (Fig. 9E)

6. Pull starter rope quickly until engine

starts.

7. Allow the engine to run for about 10

seconds. Squeeze and release throttle

trigger (D) to idle engine.

(Fig. 9F)

8. If the eingine does not start up, repeat

the above steps.

OPERATION

ENGINE PRE-START CHECKS

WARNING: Never start or operate

the saw unless the bar and chain are

properlyinstalled.

WARNING: Activate the chain brake

slowly and deliberately. Keep the chain

from touching anything; don t let the saw tip

forward.

WARNING: If chain does not

stop, turn engine off and take your unit to

the nearest Authorized Service Center for

service.

Fig. 8

TO START ENGINE

Fig. 9A Fig. 9B

Fig. 9C Fig. 9D

Fig. 9E Fig. 9F

RE-STARTING A WARM ENGINE

TO STOP ENGINE

Fig. 9G

CHAIN BRAKE OPERATIONAL TEST

TEST CHAIN BRAKEAS FOLLOWS:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Partner P340S Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info