Bedienungsanleitung Peaq PDR360BT (Seite 21 von 88) (Deutsch, Englisch, Französisch, Spanisch)

783293

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

Connections

POWER SUPPLY

Connect the plug with a power socket.

AUDIO IN

You can also listen to external audio devices by

connecting the cable (not included) to the AUDIO-

IN jack.

USB CONNECTION

Playback of music ﬁles

You can playback music ﬁles which are saved on

an USB stick by plug in the USB stick.

Charging external devices

External devices can be charged via USB port

on the unit. Connect the device to the USB port

(output: 5 V/ 1000 mA).

LAN CONNECTION

Socket of LAN / Ethernet cable connection for

the cable connection of the device with the cable-

connected home network.

HEADPHONE CONNECTION

Connect the headphones to the Headphone jack

of the device.

Attention

Danger! Excessive sound pressure levels from

ear buds and headphones can cause hearing

damage. Listening to loud music for extended

periods of time may lead to hearing impairment.

Keep the volume at reasonable levels.

REMOTE CONTROL - CHANGING BATTERY

Slide the battery compartment cover in the

direction of the arrow and pull it out. Insert the

new battery (CR2032, 3V ) , paying attention

to correct polarity. Slide the battery compartment

cover back on and let it snap into place.

Note

The battery is already inserted. Remove the battery

protection strip before ﬁrst use.

Operation

TURNING THE UNIT ON

Press the button to switch on the unit.

Note

If you turn on the product for the ﬁrst time, the

Setup Wizard will call up automatically. Follow the

on screen instructions to make the ﬁrst time set up.

Setting the display language

Press the MENU button and select System

settings. Then select Language and the desired

language, e.g. English. Press ENTER button to

conﬁrm the setting.

ADJUSTING THE ANTENNA

For optimal FM reception, extend the antenna,

move to fully extend and adjust it.

ADJUSTING THE VOLUME

The volume can be adjusted during playback with

the volume control (Tuning/Info button).

Internet-Radio Conﬁguration

There are two ways to connect the radio to the

internet using an access point:

•Wireless in WLAN-Mode

The WiFi-antenna of the radio receives your DSL

router signals

•With cable using the radio’s LAN connection

in LAN-Mode

Provided an ethernet network is available. Only

use shielded LAN cable.

WLAN-MODE CONFIGURATION

If you have a wireless network, the WLAN mode is

the direct way to connect your radio to the Internet:

1. Simply switch the radio on and, as a cable-

free network client, it automatically searches all

available APs (Access Points).

2. When switching on for the ﬁrst time, you must

conﬁrm the AP and perhaps enter the key. For

doing so please follow instructions of below

chapters. After that, the radio will always access

this AP. If the AP can no longer be found, it will

be registered accordingly.

IM_PDR360_180629_A_V04_HR.indb 21 29/6/18 5:27 pm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Peaq PDR360BT Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info