Bedienungsanleitung Peaq PDR360BT (Seite 22 von 88) (Deutsch, Englisch, Französisch, Spanisch)

783293

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Size = A5

ENGLISH

LAN CONFIGURATION

If you do not have a wireless network but do have

a cabled network, you can connect the Internet

radio with a network.

1. Switch the radio o.

2. Connect an Ethernet cable to the LAN socket.

Once switched on and choose wired. The radio

will automatically be recognized as a cable

client.

3. For manual network cable setup go to the

settings (MENU) when using Internet Radio

mode and select System Settings / Internet

Settings / Manual Settings / Cable. Select

DHCP active as the standard setting.

Note

Only use shielded LAN network cable for internet

connection via LAN. If no shielded LAN network

cable is available, please purchase a shielded LAN

network cable for the internet connection via LAN.

WLAN-REGION AND WLAN-NETWORK

Select the WLAN-Region in which you are located.

The device then looks for available wireless

networks. If a wireless network is not found, the

device shows the notiﬁcations [Rescan] [Wired]

[Manual conﬁg]. Please check in this case

whether your router and WLAN are switched on.

Note

Make sure that the DHCP-server of your router

(Access Point) is activated. Otherwise, the WLAN

connection must be conﬁgured manually. The

WLAN should send out the SSID. If the SSID is not

sent out, you must conﬁgure the WLAN manually.

•Select the network from which you want to

operate Internet radio.

PUBLIC NETWORK CONNECTION

Select the appropriate WLAN-network by clicking

on the entry of the network’s name. The connection

procedure takes place automatically.

Note

In the Systems settings > Setup wizard, you can

manually conﬁgure the network.

PRIVATE NETWORK CONNECTION

Select WPS connection type

If a network is protected by a WEP or WPA

encryption, the query for constructing a connection

over WPS (Wi-Fi Protected Setup) appears. If

the router of your wireless network has a WPS

function, select whether the WPS connection

should be established by entering a PIN code over

the WPS key on the router.

WPS connection using PIN entry

A WPS-PIN appears in the Internet radio display.

Enter this PIN and conﬁrm the Internet radio with

OK. The WPS connection will then be established.

Connection using WPS key

Press the WPS key on the router and then conﬁrm

the display on Internet radio with ENTER. The

WPS connection is then established.

CONNECTION USING THE DIRECT ENTRY OF

THE NETWORK KEY

If you do not want to establish any connection

using the WPS, select the entry, No WPS and then

enter the network key in the following dialogue.

Conﬁrm the entry with ENTER.

COMPLETING THE WLAN CONNECTION

1. The connection begins. The device should

now establish a connection with the WLAN.

Once the connection has been established,

“Connected” appears. Conﬁrm the display with

ENTER.

2. If the WLAN cannot be accessed (e.g. locked

for new WLAN devices) the failure notiﬁcation

“Connection not successful” appears.

3. In this case, check the setting of your WLAN-

router.

Note

The entered password (WEP / WPA key) will be

saved and will not need to be entered again.

IM_PDR360_180629_A_V04_HR.indb 22 29/6/18 5:27 pm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Peaq PDR360BT Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info