Bedienungsanleitung Peg Perego VIAGGIO SWITCHABLE (Seite 27 von 124) (Alle Sprachen)

626374

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

•

Ensure that the vehicle’s three-point seatbelt fixing the car

seat is always taut and not twisted. It should be replaced

in the case of heavy stress as a result of an accident.

• Never leave your child unattended in the car seat:

watch him/her even when s/he is sleeping.

• Never remove the child from the car seat when the

vehicle is in motion.

• Make sure that the car seat is not blocked by a mobile

part of the vehicle seat or by a door.

•

Adjust the height and tension of the shoulder straps,

ensuring that they are as snug to the child’s body as possible

without constricting him/her too much. Check that the

harness is not twisted and that the child does not release it.

• This car seat is not intended for prolonged periods of

sleeping.

• Do not leave the car seat in the vehicle when exposed

to the sun. Some parts might heat up and be harmful

to the delicate skin of your child. Check the seat is not

too hot before seating your child.

• Do not use the car seat without its fabric cover; this

must not be replaced with one not approved by the

manufacturer since it is an integral part of the car seat

and the safety system.

• If in doubt, contact the manufacturer or retailer of the

car seat.

• Do not remove the adhesive and stitched labels since

this might make the product not compliant with legal

requirements.

•

Do not use the car seat if it has signs of breakage or missing

parts, if it is second-hand or if it has been subjected to

heavy impacts in an accident, because it might have

suffered extremely dangerous structural damage.

• Do not alter the product.

• For any repairs, replacement parts and information

about the product, contact the after-sales assistance

service. Contact information is provided on the last

page of this manual.

• The car seat must always be secured in the vehicle,

even when the child is not sitting in it; in the event of

sudden braking, it could injure the passengers.

•

Do not use this car seat if more than seven years have

elapsed from the date of production indicated on the

structure; the natural aging of the materials may mean the

car seat is no longer compliant with safety standards.

• Do not use accessories that have not been approved by

the manufacturer or by the competent authorities.

Instructions for use

UNIVERSAL CATEGORY - Belted

Group 0+

Fastening with seatbelts

1• IMPORTANT: For the correct use of the

“Viaggio 0+1 Switchable” car seat in Group 0+

mode, it is necessary to:

- Extract from under the seat the casing that enables

the car seat to be reclined.

To extract it, press the handle and pull it towards

you, extracting the base (arrows A and B).

- Use the lever (arrow C) to recline the seat to its

highest position.

2• “Viaggio 0+1 Switchable” car seat correctly installed to

be used as a Group 0+ car seat.

3•

Install the “Viaggio 0+1 Switchable” car seat on the

vehicle’s seat so that it is rear-facing, as shown in the figure.

Pass the vehicle seatbelt between the frame and body

of the car seat following these steps:

- slip the belt into the light blue belt guides first (arrow A);

- fasten the belt, ensuring that it clicks into place (arrow B);

4• Pass the seatbelt through the upper light blue belt slot

(arrow C).

IMPORTANT: Take hold of the seatbelt and pull

it firmly, so as to ensure that the “Viaggio 0+1

Switchable” fits as close as possible to the vehicle

seat (arrow D).

Instructions for use

UNIVERSAL CATEGORY - Belted

Group 1

Fastening with seatbelts

5•

IMPORTANT: For the correct use of the “Viaggio 0+1

Switchable” car seat in Group 1 mode, it is necessary to:

- Reposition the casing within the base of the car seat.

Press the lever and push inwards, as indicated in

the figure.

6•

Install the “Viaggio 0+1 Switchable” car seat on the vehicle’s

seat so that it is front-facing, as shown in the figure.

7• To make it easier to pass the vehicle’s seatbelts

through the back of the car seat, it is necessary to

recline the car seat to its lowest position by operating

the lever, as shown in the figure.

8• Pass the vehicle seatbelt between the frame and body

of the car seat.

9• The waist strap must pass through the lower guides,

marked in red; fasten the belt, ensuring that it clicks

into place.

10• Tighten the waist strap, ensuring it has passed through

the lower guides, marked in red.

11• Bring the car seat back into the upright position by

pulling the handle below the seat (Fig. A) and pushing

the car seat as shown in the figure (Fig. B).

12• To complete the installation process, use the Steady

Fix device: open the clip and pass the diagonal strap

through it, ensuring that it is taut and not twisted (Fig.

A). Close the safety tab (Fig. B).

13• IMPORTANT: Take hold of the seatbelt and pull

it firmly upwards, so as to ensure that the “Viaggio

0+1 Switchable” fits as close as possible to the

vehicle seat (Fig. C).

Once installed, the car seat may be reclined to the

desired position (See Point 6).

How to secure your child in the

“Viaggio 0+1 Switchable” car seat

14• Before placing the child in the car seat, release the

harness by pushing the red button on the crotch strap

buckle.

15• Lift the harness and attach the buckles to the elastic

bands on the sides.

16•

Place the child in the car seat and arrange the harness over

the child’s shoulders and waist, as shown in the figure.

Peg Perego VIAGGIO SWITCHABLE Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info