Bedienungsanleitung PerfectPro SD1 - Soliddigital (Seite 7 von 33) (Deutsch, Englisch, Holländisch, Französisch)

742517

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

9 10

Calling up RDS information

When you are listening to a FM station with RDS system, repeatedly press the Info

button to cycle through the information. This will only function if the reception level is

sufcientandclear.

a. Radio text (RT) Displays the message about the station being listened

to as ticker text.

b. Program type (PTY) Displays the type of station being listened to, e.g. Pop,

Classic, News, etc.

c. Frequency Displays the frequency of the station being listened to.

d. Signal level Displays the signal strength.

e. Time & date Displays the current time (24 hour clock) and date.

Scan sensitivity setting – FM

The radio will normally scan all stations from FM broadcasts including the weaker

signals.However,youmaywishtheAuto-scantondonlythosestationswithstrong

enough signals to give good reception.

1. Press the On/Off button to turn on the radio.

2. Select the FM band by pressing the Source button.

3. Press the Menu button, the display shows “Scan setting”.

4. Press the Tuning knob.

5. Rotate the Tuning knob to select between “All stations” or “Strong station” (default

 is“Allstations”).The“Strongstation”optionwillallowtheradiotondstrongsignals

only when scanning.

6. Press the Tuningknobtoconrmyoursetting.Thedisplaywillreturntonormal

radio display.

PRESET STATIONS

Storing preset stations

There are 6 memory presets in the radio for each DAB and FM. Presets are

remembered by the radio in the event of a power failure.

1. Press the On/Off button to turn on the radio.

2. Press the Source button to select the desired waveband.

3. Tune to the required station.

4. Press and hold the required Preset button until the radio beeps and shows “Saved”.

5. Repeat step 3 and 4 for the remaining presets.

6. Stations stored in the preset memories can be over-written by following the above

procedure.

Recalling preset stations

1. Press the On/Off button to turn on the radio.

2. Press the Source button to select the desired waveband.

3. BrieyPresstherequiredPreset button. In FM mode the display will show for

example ”P1” on top right hand side.

AUX-IN MODE

A 3.5mm stereo Aux-in socket is provided on the side under the rubber cover, for

connecting an external audio radio such as MP3 player or CD player (not included with

this radio).

1. Connect an audio source to the Aux-in socket.

2. Press the Source button to select AUX input. The display will show “AUX-IN”.

3. Play the external player.

4. Adjust the volume of both the radio and the player for comfortable listening.

5. After use, close the rubber cover to prevent moist or dust from entering into the

sockets and radio.

6. If there is no Aux-in signal for an extended period of 15 minutes, the radio will

be switched off. When there is 5 minutes left, the radio will show a countdown on

the display.

Notes: Never use the Aux-in socket in rainy or moist conditions to prevent moist

from entering the radio. Keep the rubber cover closed under these conditions.

The Auto-Power management function will be activated in AUX mode. If there is no

signal* from the Aux-In socket for a period of over 15 minutes, the radio will automatically

switch to standby mode. Pressing the On/Off button will wake up the unit.

* Also when the incoming signal from the external radio is too low and cannot be

detected for a period of over 15 minutes by the Auto-Power management, the radio will

switch to standby mode.

To prevent this raise the output level of the external radio enough to be detected.

LOUDNESS

The Loudness function enables to get compensation on lower and higher frequency.

The effect will be more audible when the radio is on a lower volume level (Dynamic

Loudness).

1. Press the Loudness button to enable the loudness, the display shows “Loudness

On”.

2. Press the Loudness button again to disable the loudness, the display shows

“Loudness Off”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

PerfectPro SD1 - Soliddigital Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info