Bedienungsanleitung PerfectPro WS2BT - WORKSTATION 2 (Seite 10 von 50) (Deutsch, Englisch, Holländisch, Französisch)

742528

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

Bluetooth LED conguration

1. Press the On/Off button to turn on the radio.

2. Press the Menu button, and then rotate the Tuning knob until the display shows

“System”.

3. Press the Tuning knob; rotate the Tuning knob until the display shows “Bluetooth

LED”.

4. Press the Tuning knob to enter the Bluetooth LED adjustment menu.

5. Rotate the Tuning knob to select “on” (by default) in order to keep Bluetooth LED

lightened when connected;

6. Or rotate the Tuning knob to select “off” to turn off Bluetooth LED when Bluetooth

connection has been established.

7. Press the Tuning knobtoconrmyourchoice.

CHARGING A MOBILE PHONE

The USB socket on the left side can provide DC power of 5V/0.5A for charging a mobile

phone. Connect the mobile phone to the USB socket with an appropriate cable (not

included with this radio). The USB power is available in all modes, including standby

mode.

Refer to the user manual or the manufacturer of the mobile phone to verify if it supports

charging from an USB power.

The USB socket is suitable for DC power-out only and cannot be used for e.g. playback

of music from a USB stick.

Warning: Never use the USB socket in rainy or moist conditions to prevent moist from

entering the radio and so to prevent potential short circuit. Always keep the rubber cover

well closed under these conditions.

It is recommended to use AC power while charging a mobile phone via USB socket. On

DC power it is also possible to charge a mobile phone from the USB socket, however

using DC power to charge a mobile phone will consume energy from the batteries and

so drain the batteries easily.

OPERATING THE RADIO – AUX IN

A 3.5mm stereo Aux In socket is provided on the side behind the rubber cover, for

connecting an external audio device such as MP3 player or CD player (not included).

1. Connect a stereo or mono audio source to the Aux In socket.

2. Press the Source button to select AUX input. Display will show “AUX IN”.

3. Play the external player.

4. Adjust the volume of both the radio and the player for comfortable listening.

Notes: Never use the Aux-In socket in rainy or moist conditions to prevent moist from

entering the radio. Keep the rubber cover well closed under these conditions.

The Auto-Power management function will be activated in AUX IN mode. If there

is no signal* from the Aux-In socket for a period of over 15 minutes, the radio will

automatically switch to standby mode. Pressing the On/Off button will wake up the unit.

15 16

* Also when the incoming signal from the external device is too low and cannot be

detected for a period of over 15 minutes by the Auto-Power management, the radio will

switch to standby mode.

To prevent this raise the output level of the external device enough to be detected.

LOUDNESS

The Loudness function enables to get compensation on lower and higher frequency.

The effect will be more audible when the radio is on a lower volume level (Dynamic

Loudness).

1. Press the On/Off button to turn on the radio.

2. Press the Menu button, and then rotate the Tuning knob until the display shows

“System”.

3. Press the Tuning knob; rotate the Tuning knob until the display shows “Loudness”.

4. Rotate the Tuning knob to select between “Loudness On” or “Loudness Off”. Press

the Tuning knobtoconrmthesettingandreturntonormaldisplay.

TONE

The Tone function enables the user to adjust the lower and higher sound frequencies.

1. Press the On/Off button to turn on the radio.

2. Press and hold the Volume knob for about 3 seconds, the display shows “BASS 0”.

3. Rotate the Volume knob to set the desire Bass level.

4. Press the Volume knobtoconrm,thedisplayshows“TREBLE0”.

5. Rotate the Volume knob to set the desire Treble level.

6. Press the Volume knobtoconrmandreturntonormaldisplay,

METAL TELESCOPIC ANTENNA

You can use this as an alternative antenna for your radio in areas or locations where the

radio signal (FM/DAB/DAB+) is weak to very weak.

ATTENTION: The standard antenna on the radio is exible. The metal antenna

is not exible or bendable and should be used with care. Breaking or bending

antennas is not covered by warranty.

Installing:Carefullyscrewoffthestandardexibleantenna.Firstcarefullyloosenthe

antenna with an open-end-wrench key (size 14) – turn counter clockwise. Carefully

screw on the metal telescopic antenna and softly tighten it with an open-end-wrench key

(size 14) – turn clockwise.

ATTENTION: do not use too much force when xing the antennas as this can

damage the screw threat of the antennas or make it break off

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

PerfectPro WS2BT - WORKSTATION 2 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info