Bedienungsanleitung Petsafe PIG00-11116 (Seite 10 von 19) (Englisch)

770992

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

petsafe.com1-800-732-2677 1918

Test the Receiver Collar

Traditional Mode (B) Installation

These steps are very similar to the ones we used in Step 8.

1. Set the fence transmitter to mode (B) and turn the boundary width

dial up to 7 (9E).

2. Make sure that the static correction on the receiver collar is set to

level 6.

3. Place the test light tool against the receiver collar contact points

and hold the contact points facing upwards.

4. Hold the receiver collar at your pet’s neck height (9F).

5. Starting inside the pet area, slowly approach the boundary

wire until you hear the warning tone (9G). 2 seconds later, the

test light will begin to flash. Walk back into the pet area until the

beeping stops.

6. Adjust the boundary width dial to set the warning zone

appropriately. We recommend setting it so that the warning zone

begins at least 10 ft. before the boundary wire.

7. Repeat this test at different places along the boundary wire to

verify that it is working everywhere.

Note: To ensure that the signal is not coupled to any wires or other

metallic objects, we will do one more test inside the pet area.

8. With the test light tool and receiver collar contact points facing

upward, walk throughout the pet area (9H).

9. If the receiver collar does not activate in the pet area (where it

should not) then things are going great.

10. If the receiver collar does activate within the pet area, it means

that you need to adjust the boundary wire where it crosses a

cable or electrical wire or approaches another metallic object.

Refer back to the instructions in Step 1. After the adjustment, retest

the system.

11. Now that the boundary width is established, set the correction

level on the receiver collar to level 1 for training.

12. Now it is safe to bury your boundary wire!

A B

Set the dial

to 7

Mode B

Boundary

Wire

Pet Area

Step 10: Bury the Boundary Wire

• Underground cables can carry high voltage. Have all underground cables marked before you dig to bury your

wire. In most areas, this is a free service. Avoid these cables when you dig.

• Before you begin installing the boundary wire, turn the fence transmitter off and unplug the adaptor from the

surge protector.

Burying the boundary wire is recommended to protect it and prevent

disabling the system.

1. Cut a trench 1–3 inches deep along your planned boundary. It

only needs to be as wide as the wire.

Quick Tip: We have tried lots of tools. Lawn trenchers, which you

can often rent from a local hardware store, work great and make for

a quick job. You can also use a flat shovel, like a trenching shovel.

2. Place the boundary wire into the trench maintaining some slack to

allow it to expand and contract with temperature variations.

3. Use a blunt tool such as a wooden paint stick to push the

boundary wire into the trench. Be careful not to damage the

boundary wire insulation.

Utilizing an Existing Fence

The boundary wire can be attached to a chain link fence, split

rail fence or a wooden privacy fence. The boundary wire can be

attached as high as needed. However, make sure the boundary

width is set at a high enough range for your pet to receive the signal.

If using a double loop (Traditional mode (B) only) with an existing

fence at least 5 ft. tall, run the boundary wire on top of the fence and

return it on the bottom of the fence to get the 5 ft. separation needed.

• Chain Link Fence (10A):

Weave the boundary wire through the links or use plastic

quick ties.

• Wooden Split Rail or Privacy Fence (10A):

Use staples to attach the boundary wire. Avoid puncturing the

insulation of the boundary wire.

• Double Loop with an Existing Fence:

Run the boundary wire on top of the fence and return it on the

bottom of the fence to get the 5 ft. separation needed.

• Gate (Single Loop) (10B):

Bury the boundary wire in the ground across the gate opening.

Note: The signal is still active across the gate. Your pet cannot

pass through an open gate.

• Gate (Double Loop) (10B):

Bury both boundary wires across the gate opening while keeping

them 5 ft. apart.

Follow all safety instructions for your power tools. Be sure to always wear your safety goggles.

Single Loop

Double Loop

5' 5'

10B

Weave Wire Into Fence

Staple Wire Into Fence

10A

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Petsafe PIG00-11116 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info