Bedienungsanleitung Petsafe PIG00-11116 (Seite 11 von 19) (Englisch)

770992

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

petsafe.com1-800-732-2677 2120

Cross Hard Surfaces (driveways, sidewalks, etc.)

• Concrete Driveway or Sidewalk (10C): Place the boundary

wire in a convenient expansion joint or create a groove using a

circular saw and masonry blade. Place the boundary wire in the

groove and cover with an appropriate waterproofing compound.

For best results, brush away dirt or other debris before patching.

• Gravel or Dirt Driveway (10D): Place the boundary wire

in a PVC pipe or water hose to protect the boundary wire

before burying.

Step 11: Place the Boundary Flags

The boundary flags are visual reminders for your pet of where the

warning zone is located.

1. Place the test light contacts on the contact points. Hold the

receiver collar at the height of your pet’s neck.

2. Walk towards the warning zone until the receiver collar

beeps (11A).

3. If you are in YardMax® mode (A) place the boundary flag

along the boundary wire approximately 6 inches inside the pet

area

(11B).

4. If you are in Traditional mode (B) place the boundary flag where

you hear the beep

(11C ).

5. Walk back into the pet area until the beeping stops.

6. Repeat this process along the warning zone until it is marked with

boundary flags every 10 ft.

(11D)

10C 10D

Boundary

Wire

YardMax® Mode (A)

11A

Boundary

Wire

Pet

Area 6 in.

11B

Boundary

Wire

Traditional Mode (B)

11C

10 ft.

11D

Step 12: Fit the Receiver Collar

Proper fit of the receiver collar is important. A receiver collar worn for too long or made too tight on your pet’s neck

may cause skin damage, ranging from redness to pressure ulcers. This condition is commonly known as bed sores.

• Avoid leaving the receiver collar on your pet for more than 12 hours per day.

• When possible reposition the receiver collar on your pet’s neck every 1 to 2 hours.

• Check the fit to prevent excessive pressure; follow the instructions in this manual.

• Never connect a leash to the receiver collar; it will cause excessive pressure on the contact points.

• When using a separate collar for a leash, do not put pressure on the receiver collar.

• Wash your pet’s neck area and the contact points of the receiver collar weekly with a damp cloth.

• Examine the contact area daily for signs of a rash or a sore.

• If a rash or sore is found, discontinue use of the receiver collar until the skin has healed.

• If the condition persists beyond 48 hours, see your veterinarian.

• For additional information on bed sores and pressure necrosis, please visit our website.

These steps will help keep your pet secure and comfortable. Millions of pets are comfortable while they wear stainless

steel contact points. Some pets are sensitive to contact pressure. You may find after some time that your pet is very

tolerant of the receiver collar. If so, you may relax some of these precautions. It is important to continue daily checks of

the contact area. If redness or sores are found, discontinue use until the skin has fully healed.

Important: The proper fit and placement of your receiver collar is

important for effective training. The contact points must have direct

contact with your pet’s skin on the underside of his neck.

1. Be sure the receiver collar is off before placing it on your pet.

Then with your pet standing, fit the receiver collar snugly onto

your pet’s neck so that the contact points make contact with your

pet’s skin on the underside of his or her neck. Make sure the

PetSafe® logo is right-side up (12A).

2. Check the tightness of the receiver collar by inserting one finger

between the end of a contact point and your pet’s neck. The fit

should be snug but not constricting.

3. Allow your pet to wear the receiver collar for a few minutes, then

check it again.

You may need to trim the hair in the area of the contact points. Never shave your pet’s neck; this may lead to a rash or infection.

4. Once you are satisfied with the fit of the receiver collar, remove it

from your pet and trim it, but make sure to allow room for growth

or a thicker winter coat. Use a lighter to seal the cut so that it will

not fray (12B).

5. The collar will slip if it is not properly threaded. The slide buckle

prevents the collar from becoming loose around your pet’s neck

and the ridges must be facing up (12C).

6. While the receiver collar is still off your pet, turn it on by holding

the mode button until a green light comes on. The first thing

your receiver collar does is a ReadyTest® startup (Step 7) to

ensure that it is ready for use. You will know it is done when the

indicator flashes the series of red flashes to indicate the current

static correction level. Do not touch the contact points during the

ReadyTest® startup.

12A

12B

Slide Buckle

Ridges

12C

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Petsafe PIG00-11116 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info