Bedienungsanleitung Petsafe PPA19-16811 (Seite 4 von 49) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

770959

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

4petsafe.com

ENFRES

2. Drill four corner holes with a 12 mm (½”) diameter drill bit as marked on

the Cutting Template through the door. Ensure that the drill remains straight

and level.

3. Using a jig or key-hole saw, cut along the appropriate line as indicated

on the Cutting Template. (Fig. D).

4. Temporarily place the interior frame into the cutout. Level

the cat ﬂap until it is in the proper position in the center

of the cutout. On the outside install the exterior frame.

Use a pencil to mark screw holes through the mounting

holes on the exterior frame (Fig. E).

5. Remove the interior and exterior frame and drill the

screw holes with a 6mm (¼”) drill bit (Fig. F). Ensure

that the drill remains straight and level.

6. Clean the area from any dust, dirt or debris.

7. From the interior of the home, insert the cat ﬂap interior

frame into the opening.

8. From the exterior of the home, place the exterior frame

onto the interior frame.

9. Making sure to center the cat ﬂap in the hole. Three (3) different lengths

of screws have been provided with this cat ﬂap. Select the appropriate

length. Using a manual screw driver, screw the exterior frame to the

interior frame.

10. Insert the two blanking plugs over the screws on the exterior frame.

11. Remove the batteries from the cat ﬂap and wait for 30 seconds. Re-install

the batteries and battery cover. The cat ﬂap is ready to use.

Fig. E

Fig. F

The PetSafe® Microchip Cat Flap is suitable to ﬁt most doors or partitions although

additional materials and competent DIY skills may be required. This cat ﬂap is

designed to adapt easily to cut-out sizes for Staywell® 200, 300, 400, 500, 900

and Petporte smartﬂap™ series cat ﬂaps. Some simple DIY skills are required and

minor adjustments to the cut-out or additional accessories might be needed.

Installation

–

Measurement and Marking

Measure the belly height

of your cat. This is usually

100 mm (3 ¹

₅

⁄₁₆”) –150 mm

(5 ¹

₅

⁄₁₆”) (Fig. A).

Mark this measurement on the

outside of your door and draw

a straight horizontal line 168 mm (6

₅

⁄₈”) long, preferably in the center of the

door (Fig. B).

Please keep in mind that this horizontal line will eventually be the bottom of the

hole you will cut in your door. The frame of the cat ﬂap will be 25 mm lower. If

an installation adaptor is used, then the frame will be lower.

Note: This line may have to be raised slightly to allow for at least 50 mm (2”)

from the bottom of the door.

Important: Do not cut the tunnel. Key components are contained

within the tunnel and any alteration to the tunnel will affect functionality.

Installation – Wooden, PVC, or uPVC

Doors without Metal

Before beginning, please check if your door has a metal core. If a metal core

or metal plate is found, follow the

Installation – Metal or Metal Core

Doors instructions.

1. Attach the supplied Cutting Template

to the outside of your door in the

correct position ensuring that it is the

right way up and level (Fig. C).

(x)

Fig. A

(x)

Fig. B

(X)

Fig. C

(X)

Fig. D

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Petsafe PPA19-16811 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info