501663
26
Zoom out
Zoom in
Vorherige Seite
1/61
Nächste Seite
EN 26
More sound settings
You can change the settings in the Sound
menu.
1. Press .
2. Select [Setup] > [TV settings] > [Sound],
then press OK.
3. Select a setting to change, then press OK:
[Smart sound]: Access predefined
smart sound settings.
[Reset]: Reset to factory default
settings.
[Clear Sound]: Enhance the sound
quality.
[Bass]: Change the bass level.
[Treble]: Change the treble level.
[Surround]: Switch on spatial sound.
[Auto volume levelling]: Automatically
reduce sudden volume changes, for
example when switching channels.
[Headphone volume]: Change
headphone volume.
[Balance]: Change the balance of the
left and right speakers.
[Audio out delay]: Automatically sync
the image on the TV to the audio from
a connected home theatre.
[Audio out offset]: Change the setting
for audio output delay. You cannot
select this setting if [Audio out delay] is
not switched on.
[Digital output format]: Select audio
output through the digital audio
connector. Select [PCM] to convert
non-PCM audio or [Multichannel] to
output to home theatre.
[Digital output level]: Set the sampling
rate for PCM audio.
[Normal] - No loss in intensity or signal
strength; [Low] - Certain amount of
loss in intensity or signal strength.
Select audio format
If a digital TV channel broadcaster streams
audio in several formats, you can select an
audio format.
1. Press .
2. Select [Setup] > [Channel settings] or
[Satellite settings] > [Language].
3. Select a setting, then press OK:
[Preferred audio format]: Receive
standard audio format (MPEG) or
advanced audio formats (AAC, EAC-3
or AC-3 if available).
[Mono/Stereo]: If stereo broadcasting is
available, select mono or stereo audio.
4. Press to exit.
Reset picture and sound
You can restore the default picture and
sound settings, while the channel installation
settings remain the same.
1. While you watch TV, press .
2. Select [Setup] > [TV settings] > [Factory
settings], then press OK.
All TV settings (except for channel settings)
are reset to the default factory settings..
Channel settings
Automatic install
When the TV was switched on for the first
time, a full installation of channels was
performed. To change your language,
country and reinstall all available TV channels,
you can run this full installation again.
Start installation
1. Press .
2. Select [Setup] > [Search for channels] >
[Reinstall channels], then press OK.
The Country menu is displayed.
3. Select your country, then press OK.
4. Select your network, then press OK:
[Antenna]: Access free-to-air antenna
or digital DVB-T channels.
[Cable]: Access cable or digital DVB-C
channels.
26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Philips 32PFL3107 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Philips 32PFL3107

Philips 32PFL3107 Bedienungsanleitung - Deutsch - 69 seiten

Philips 32PFL3107 Bedienungsanleitung - Holländisch - 65 seiten

Philips 32PFL3107 Bedienungsanleitung - Französisch - 68 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info