Bedienungsanleitung Philips 49PUS6501 (Seite 87 von 107) (Englisch)

628877

Zoom out

Zoom in

Vorherige Seite

1/107

Nächste Seite

7 - Select Finish and press OK to store the

channels and radio stations.

Remove a Satellite

You can remove one or more satellites from your

current satellite installation. You remove the satellite

and its channels. Some satellite operators do not

allow removing a satellite.

To remove satellites…

1 - Press



, select All Settings and press OK.

2 - Select Channels > Satellite Installation and

press OK.

3 - Select Search for satellite and press OK.

4 - Select Remove Satellite and press OK. The

current satellites are shown.

5 - Select a satellite and press OK to mark or

unmark them to remove.

6 - Press



(left) repeatedly if necessary, to close

the menu.

Manual Installation

Manual Installation is intended for expert users.

You can use Manual Installation to quickly add new

channels from a satellite transponder. You need to

know the frequency and polarization of the

transponder. The TV will install all channels of that

transponder. If the transponder was installed before,

all its channels - the former and the new ones - are

moved to the end of the channel list All.

You cannot use Manual installation if you need to

change the number of satellites. If this is needed, you

have to do a complete installation with Install

Satellites.

To install a transponder…

1 - Press



, select All Settings and press OK.

2 - Select Channels > Satellite Installation and

press OK.

3 - Select Manual Installation and press



(right)

to enter the menu.

4 - If you have more than 1 satellite installed, select

LNB for which you want to add channels.

5 - Set the Polarisation you need. If you set

the Symbol Rate Mode to Manual, you can enter

the symbol rate in Symbol Rate manually.

6 - Press the arrows



(up) or



(down) to adjust

the frequency, and select Done.

7 - Select Search and press OK. The signal

strenght is shown on screen.

8 - If you want to store the channels of a new

transponder, select Store and press OK.

9 - Press



(left) repeatedly if necessary, to close

the menu.

Homing Transponder and LNB

In some countries, you can adjust the expert settings

for homing transponder and each LNB. Only use or

change these settings when a normal installation fails.

If you have non-standard satellite equipment, you

can use these settings to overrule the standard

settings. Some providers might give you some

transponder or LNB valeus which you can enter here.

LNB Power

By default, LNB Power is set to On.

22 kHz Tone

By default, the Tone is set to Auto.

Low LO Frequency / High LO Frequency

The local oscillator frequencies are set to standard

values. Adjust the values only in case of exceptional

equipment that needs different values.

Problems

The TV cannot find the satellites I want or the TV

installs the same satellite twice

• Make sure that the correct number of satellites is set

in Settings at the start of the installation. You can set

the TV to search for One, Two or 3/4 satellites.

A dual head LNB cannot find a second satellite

• If the TV finds one satellite but cannot find a second

one, turn the dish a few degrees. Align the dish to get

the strongest signal on the first satellite. Check the

signal strength indicator of the first satellite on screen.

With the first satellite set at the strongest signal, select

Search again to find the second satellite.

• Make sure the settings are set to Two Satellites.

Changing the installation settings did not solve my

problem

• All settings, satellites and channels are only stored

at the end of the installation when you finish.

All satellite channels are gone

• If you use a Unicable system, make sure you

assigned two unique user band numbers for both

built-in tuners in the Unicable settings. It might be

that another satellite receiver in your Unicable system

is using the same user band number.

Some satellite channels seem to have disappeared

from the channel list

• If some channels seem to be gone or displaced, the

broadcaster might have changed the transponder

location of these channels. To restore the channel

positions in the channel list, you can try an update of

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips 49PUS6501 Seite 87

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips 49PUS6501

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info