Bedienungsanleitung Philips CRYSTAL650 (Seite 57 von 80) (Englisch)

26364

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

2. Networks 57

2. Networks

You can connect your multifunction machine to a PC

with a USB cable or to a PC or network via a wireless

connection.

With the USB cable, you can connect your multifunction

machine to a PC that is connected to a network. Other

PCs on this network can then access the multifunction

machine if it is shared for use on the network. You can-

not connect the machine directly to a network over the

USB cable!

With a WLAN adapter, it is possible to integrate the

multifunction machine into an existing wireless net-

work as a network printer. It functions only with an

original adapter, which you can purchase through our

order service (see the back page of this user manual).

More information: www.fax.philips.com

Wireless Networks

One refers to a wireless network or WLAN (Wireless

Local Area Network) if at least two computers, printers

or other devices communicate in a network over radio

waves (high frequency waves). e data transmission in

the wireless network is based on the TCP/IP protocol.

Depending on the way the network is structured, it is

referred to either as an infrastructure or ad-hoc net-

work.

Infrastructure Wireless Network

In an infrastructure network, multiple devices commu-

nicate via a central access point (gateway, router). All

data are sent to the access point (gateway, router) and

distributed from there.

Ad-hoc Wireless Network

In an ad-hoc network, the devices communicate with

each other equally, without an access point (gateway,

router) acting as intermediary. e transmission rate

in an entire ad-hoc wireless network depends on the

worst connection in the network. e transmission rate

depends on the spatial distance as well as obstacles be-

tween the sender and receiver such as walls or ceilings.

Setting Up Wireless

Networks (WLAN)

ree steps are required to integrate your multifunction

machine into a wireless network (WLAN):

1 Conﬁgure the network on your PC.

2 Conﬁgure your multifunction machine for net-

work operation.

3 Install the software C S IH with the

required printer drivers on your PC after you have

conﬁgured the machine.

Before you conﬁgure the multifunction ma-

chine, the network must be set up on your PC

and, if applicable, on all connected devices (other

PCs, access point, gateway, router) and must be

functioning. All required information for conﬁg-

uration of the machine, such as network names

(SSID), radio channel, WEP key, IP address or

subnet mask must match the information of the

network. You can ﬁnd this information on your

PC under S > S > N C-

. Select the WLAN there. Consult the

user manual of your WLAN adapter for instruc-

tions on how to conﬁgure the wireless network

on your PC. In larger networks, consult your

network administrator.

Faultless communication is ensured if you

also use an original adapter on your PC (see

order service on the back page of this user man-

ual). e newest drivers for the original adapt-

er and other information can be found on our

Internet page: www.fax.philips.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips CRYSTAL650 Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips CRYSTAL650

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info