Bedienungsanleitung Philips DVP-620VR (Seite 7 von 20) (Englisch)

584558

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Turning on your DVD/ VCR

The following steps only be performed when you insert the AC

PLUG at the first time.

1 Turn on the TV and select the

video channel on the TV.

Plug in the DVD/VCR.

3 Press K/L repeatedly to select

your desired language.

4 Press DISC/VCR MENU.

5 Confirm with P+.

The automatic TV channel search

starts.

6 “TIME” and “DATE” will appear on

the TV screen.

7 Check “TIME”. If required, please

change the time with numerical key

pads.

8 Check if the displayed settings for

“DAY”, “MONTH” and “YEAR” are

correct.

9 When all information is correct,

save by pressing STATUS/EXIT.The

preparation for use is now

complete.

Note:

– When AUTO TUNING has been completed, the initial

settings menu will not appear even if the AC plug has

been unplugged or after a power failure.To recall this

initial settings menu, press SOURCE and PLAY at the

same time for more than 2 seconds on the system’s

front panel.

Playable Video Cassette Tapes

Philips Consumer Electronics recommends that only video

cassette tapes that have the VHS mark and High Quality (HQ)

system is compatible with this DVD/VCR.This

DVD/VCR has an Automatic Head Cleaner.

Recording Prevention

Video cassette tapes have record tabs to

ensure recordings are not erased accidentally.

1 To prevent recording, break off the tab with a

screw-driver.

2 To allow recording, cover the hole with

cellophane tape.

Notes:

– Use only tapes with VHS mark.

– Remove any adhesive stick-on notes from the tape

before inserting into the DVD/VCR.

– Periodic maintenance is required to maintain your DVD/

VCR performance.

– Video heads will require replacement after a period of

time. Only an authorised service center should perform

this service.

Using the Remote Control

• Direct the remote control at the remote sensor of the DVD/

VCR.

• Do not drop the remote control.

• Do not leave the remote control near extremely hot or

humid place.

• Do not spill water or put anything wet on the remote control.

Inserting batteries into the Remote Control

1 Open the battery cover.

2 Insert batteries (AA size) with the

correct polarity as indicated by the

and - symbols inside the battery

compartment.

3 Close the cover.

CAUTION!

– Remove batteries if they are exhausted or not to be used

for a long time.

– Do not use old and new or different types of batteries in

combination.

– Batteries contain chemical substances, so they should be

disposed off properly and kept away from children.

External Input Mode (for VCR features)

To r eceive the signal from an external input (decoder, satellite

receiver, video camera, another VCR etc.), connect to the AV2

(DECODER) socket, and enter ‘0.0.2.’ with numerical key pads

to appear “AV2” on the TV screen.

If you use the AV1 (TV) socket, enter ‘0.0.1.’ with numerical key

pads to appear “AV1” on the TV screen.

If you use the front AUDIO/VIDEO in jacks, enter ‘0.0.3.’ with

numerical key pads to appear “AV3” on the TV screen.

English

Setting Up your DVD/ VCR

PLEASE WAIT

START FINISH

❚❚❚❚❚❚❚❚❚❚❚

❚❚❚❚❚❚❚❚❚❚❚❚❚

SELECT KL

→ ENGLISH

FRANÇAIS

ESPAÑOL

DEUTSCH

ITALIANO

SVENSKA

NEDERLANDS

PUSH MENU TO CONTINUE

Video Channel Setting

Video channel setting will be necessary, if your DVD/VCR is

connected to the TV via the coaxial cable.

1 Insert a pre-recorded tape into the DVD/VCR.The DVD/VCR

will turn on and start playback automatically.

If playback does not start, press PLAY B .

2 Select and adjust your TV to channel 36.

• If the playback picture appears on the TV screen, continue

with step 8.

• If channel 36 is employed for broadcasting, or interference

lines appear on the picture, the RF converter must be set to

a different channel between CH22 and CH69. Continue with

step 3.

3 Press DISC/VCR MENU.

4 Press K/L to select “INITIAL SET

UP”.Then, press B.

5 Press K/L to select “RF OUT”.

Then, press B twice.

6 Press K/L to select a channel

which is not used for broadcasted

between channel 22 and channel 69

in your area, then press B.

• You can also see the selecting RF channel in the display

7 Press STATUS/EXIT to exit.

Set the TV channel to the RF OUT CHANNEL which was

selected on the DVD/VCR. A picture from the VCR will appear

on the TV screen. If a picture does not appear, repeat steps 3

to 7 using a different channel which is not used for

broadcasted.

8 Press STOP C to stop the tape.

Note:

– You may also access the RF OUT CH menu by pressing

and holding DISC/VCR MENU for 3 seconds during

power off until the RF OUT CH menu appears.

SELECT KL CHOOSE B

→ RF OUT CH 36

SET=0-9

END=EXIT

TIME 10:00

DATE 25/ 12/ 04

SMART CLOCK [ON]

END=EXIT

H9720ED.qx3 04.4.16 10:43 AM Page 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips DVP-620VR Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips DVP-620VR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info