Bedienungsanleitung Philips EP2230 (Seite 15 von 28) (Englisch)

684444

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

When you use the machine for the first time, the AquaClean light starts flashing

orange. This indicates that you can start using the AquaClean water filter. If you do

not activate an AquaClean water filter, the light will switch off automatically after a

while.

Once you have installed the filter and activated it with the AquaClean icon, the

AquaClean light turns blue to confirm that the AquaClean water filter is active.

When the filter is exhausted, the AquaClean light starts flashing orange again to

remind you to replace the filter with a new one.

When the orange AquaClean light is off, you can still activate an AquaClean filter,

you will need to descale the machine first.

Activating the AquaClean water filter (5 min.)

The machine does not automatically detect that a filter has been placed in the water tank.

Therefore you need to activate each new AquaClean water filter that you install with the AquaClean

icon.

When the orange AquaClean light is off, you can still activate an AquaClean water filter, but you will

need to descale the machine first.

Your machine has to be completely limescale-free before you start to use the AquaClean water

filter.

Before activating the AquaClean water filter, it has to be prepared by soaking it in water as described

below. If you don't do this, air might be drawn into the machine instead of water, which makes a lot of

noise and prevents the machine from being able to brew coffee.

1 Shake the filter for about 5 seconds (Fig. 38).

2 Immerse the filter upside down in a jug with cold water, shake/press it a bit and wait until no more

air bubbles come out (Fig. 39).

3 The filter is now prepared for use and can be inserted into the water tank.

4 Insert the filter vertically onto the filter connection in the water tank. Press it down to the lowest

possible point (Fig. 40).

5 Fill the water tank with fresh water and place it back into the machine.

6 If attached, remove the LatteGo.

7 Place a bowl under the hot water spout/milk frother.

8 Press the AquaClean icon for 3 seconds (Fig. 41). The start light starts to pulse.

9 Press the start/stop button to start the activation process.

10 Hot water will be dispensed from the hot water spout/milk frother (3 min.).

11 When the activation process is finished, the blue AquaClean light goes on to confirm that the

AquaClean water filter has been activated correctly.

Replacing the AquaClean water filter (5 min.)

After 95 liters of water have flowed through the filter, the filter will cease to work. The AquaClean light

turns orange and starts to flash to remind you to replace the filter. As long as it flashes, you can

replace the filter without having to descale the machine first. If you do not replace the AquaClean

water filter, the orange light will go out eventually. In that case you can still replace the filter but you

first need to descale the machine.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips EP2230 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips EP2230

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info