Bedienungsanleitung Philips FC8772 Robot - SmartPro Compact (Seite 7 von 130) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

673188

Zoom out

Zoom in

Vorherige Seite

1/130

Nächste Seite

How your robot cleans

Cleaning system

The robot has a 2-stage cleaning system to clean your floors efficiently.

The two side brushes help the robot clean in corners and along walls. They also help to remove dirt

from the floor and move it towards the suction opening (Fig. 4).

The suction power of the robot picks up loose dirt and transports it through the suction opening

into the dust container (Fig. 5).

Cleaning patterns

In its auto cleaning mode, the robot uses an automatic sequence of cleaning patterns to clean each

area of the room optimally. The cleaning patterns it uses are:

1 Z-pattern or zigzag pattern (Fig. 6)

2 Random pattern (Fig. 7)

3 Wall-following pattern (Fig. 8)

4 Spot-cleaning pattern (Fig. 9)

In its auto cleaning mode, the robot uses these patterns in a fixed sequence:z-pattern, random

pattern, wall-following pattern, and spot-cleaning pattern.

When the robot has completed this sequence of patterns, it starts moving in Z-pattern again. The

robot continues to use this sequence of patterns to clean the room until the rechargeable battery runs

low, or until it is switched off manually.

Note: You can also select each mode individually by pressing the appropriate button on the remote

control. For more details, see chapter 'Using your robot', section 'Cleaning modes'.

How your robot avoids height differences

The robot has three drop-off sensors in its bottom. It uses these drop-off sensors to detect and avoid

height differences such as staircases.

Note: It is normal for the robot to move slightly over the edge of a height difference, as its front drop-

off sensor is located behind the bumper.

Caution: In some cases, the drop-off sensors may not detect a staircase or other height difference

in time. Therefore monitor the robot carefully the first few times you use it, and when you operate it

near a staircase or another height difference. It is important that you clean the drop-off sensors

regularly to ensure the robot continues to detect height differences properly (see chapter ' Cleaning

and maintenance' for instructions).

Before first use

Mounting the side brushes

1 Unpack the side brushes and place the robot upside down on a table or on the floor.

2 Push the side brushes onto the shafts on the bottom of the robot (Fig. 10).

Note: Make sure you attach the side brushes properly. Press them onto the shaft until you hear

them lock into position with a click.

Removing the protection tag from the remote control

The remote control works on a CR2025 coin-shaped battery. This battery is protected with a

protection tag that has to be removed before use.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips FC8772 Robot - SmartPro Compact Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips FC8772 Robot - SmartPro Compact

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info