Bedienungsanleitung Philips FC8772 Robot - SmartPro Compact (Seite 9 von 130) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

673188

Zoom out

Zoom in

Vorherige Seite

1/130

Nächste Seite

Note: The robot only searches for the docking station automatically when it started cleaning from the

docking station.

Preparing the room for a cleaning run

Before you start the robot on its cleaning run, make sure that you remove all loose and fragile objects

from the floor (Fig. 18).

Also remove all cables, wires and cords from the floor.

Using your robot

Starting and stopping

1 Press the start/stop button.

You can press the start/stop button on the robot (Fig. 19).

You can also press the start/stop button on the remote control (Fig. 20).

2 The start/stop button is continuously on and the robot starts cleaning (Fig. 21).

3 The robot cleans in the auto-cleaning mode until its battery runs low. In the auto-cleaning mode, it

follows repeated sequences of Z-pattern, random, wall-following and spot-cleaning patterns (Fig.

22).

Note: To select an individual mode, press one of the mode buttons on the remote control. See

section 'Cleaning mode selection' for more details.

4 When the battery runs low, the start/stop button starts flashing and the robot searches for the

docking station to recharge (Fig. 17).

5 You can also press the start/stop button to interrupt or stop the cleaning run. If you press the

start/stop button again and there is still enough energy in the rechargeable battery, the robot

continues cleaning in the auto-cleaning mode.

6 To make the robot return to the docking station before the rechargeable battery runs low, press

the docking button on the remote control (Fig. 23).

The start/stop button starts flashing and the robot searches for the docking station (Fig. 24).

Note: If you did not start the robot from the docking station, it does not search for the docking

station automatically when the rechargeable battery runs low. If there is still enough energy in the

rechargeable battery, you can press the docking button on the remote control to make the robot

return to the docking station. If the rechargeable battery is completely empty, you have to place

the robot on the docking station manually.

Operating the docking station

The docking station has two controls that can be used to operate the robot.

Battery full and go button

If you press the battery full and go button on the docking station while the robot is charging, the robot

starts cleaning as soon as the rechargeable battery is full (Fig. 25).

24h button

If you press the 24h button on the docking station, the docking station starts to count down the 24

hours until the next cleaning run. When the countdown is finished, the robot starts cleaning until its

battery runs low and then returns to the docking station automatically to recharge (Fig. 26).

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips FC8772 Robot - SmartPro Compact Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips FC8772 Robot - SmartPro Compact

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info