Bedienungsanleitung Philips gc2505 (Seite 3 von 9) (Englisch)

323563

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

out of the soleplate during ironing), use the Calc-Clean

function more frequently.

1 Make sure the appliance is unplugged.

2 Set the steam control to position O.

3 Fill the water tank to the maximum level.

Do not pour vinegar or other descaling agents into the

water tank.

4 Set the temperature dial to MAX (Fig. 11).

5 Plug in the appliance. If the appliance has an earthed

plug, put the mains plug in an earthed wall socket.

6 Unplug the iron when the temperature light goes

out.

7 Hold the iron over the sink and set the steam

control to the Calc-Clean position ( 1). The steam

control springs up slightly.

8 Pull the steam control upwards and remove

it (Fig. 12).

9 Hold the iron over the sink and move it to and

fro (Fig. 13).

Steam and boiling water come out of the soleplate.

Impuritiesandakes(ifany)areushedout.

10 Use vinegar to remove scale, if any, from the steam

control needle (Fig. 14).

Do not bend or damage the steam control needle.

11 Put the steam control back into the iron. Insert

the point of the needle exactly in the centre of the

holeandtthesmallprojectiononthesideofthe

needle into the slot. Press down the steam control

while you turn it to position O (Fig. 15).

12 Repeat the Calc-Clean process if the iron still

contains a lot of impurities.

After the Calc-Clean process

1 Put the plug back into the wall socket and let the

iron heat up to let the soleplate dry.

2 Unplug the iron when the temperature light goes

out.

3 Move the iron gently over a piece of used cloth to

remove any water stains that may have formed on

the soleplate.

Storage

1 Set the steam control to position O, remove the

plug from the wall socket and let the iron cool

down.

2 Wind the mains cord round the cord storage

facility (Fig. 16).

3 Store the iron on its heel in a safe and dry place.

Environment

Do not throw away the appliance with the normal

household waste at the end of its life, but hand it in

at an ofcial collection point for recycling. By doing

this, you help to preserve the environment (Fig. 17).

Guarantee & service

If you need service or information or if you have a

problem, please visit the Philips website at www.philips.

com or contact the Philips Consumer Care Centre

in your country (you nd its phone number in the

worldwide guarantee leaet). If there is no Consumer

Care Centre in your country, go to your local Philips

dealer.

Troubleshooting

This chapter summarises the most common problems

you could encounter with the appliance. If you are unable

to solve the problem with the information below, contact

the Consumer Care Centre in your country.

Problem Cause Solution

The iron is

plugged in, but

the soleplate is

cold.

There is a connection

problem.

Check the mains cord, the plug and

the wall socket.

The temperature dial

is set to MIN.

Set the temperature dial to the

required position.

The iron does

not produce any

steam.

There is not enough

water in the water

tank.

Fill the water tank (see chapter

‘Preparing for use’, section ‘Filling the

water tank’).

The steam control is

set to position O.

Set the steam position to ç or é

(see chapter ‘Using the appliance’,

section ‘Steam ironing’).

The soleplate is not

hot enough and/or

the drip-stop function

has been activated

(specic types only).

Set an ironing temperature that is

suitable for steam ironing ( 2 to

MAX). Put the iron on its heel and

wait until the temperature light goes

out before you start ironing.

The shot-of-

steam function

does not work

(specic types

only).

You have used

the shot-of-steam

function too often

within a very short

period.

Continue ironing in horizontal position

and wait a while before you use the

shot-of-steam function again.

The iron is not hot

enough.

Set an ironing temperature that is

suitable for steam ironing ( 2 to

MAX). Put the iron on its heel and

wait until the temperature light goes

out before you start ironing.

Flakes and

impurities come

out of the

soleplate during

ironing.

Hard water forms

akes inside the

soleplate.

Use the Calc-Clean function one or

more times (see chapter ‘Cleaning

and maintenance’, section ‘Calc-Clean

function’).

The light on

the handle

ashes (specic

types only).

The automatic shut-off

function has been

activated (see chapter

‘Features’, section

‘Automatic shut-off’).

Pick the iron up or move it slightly

to deactivate the automatic shut-off

function. The automatic shut-off light

goes out.

There are water

droplets on the

fabric.

You have not closed

the cap of the lling

opening properly.

Press the cap until you hear a click.

There are water

droplets on the

fabric (specic

types only).

The set temperature

is too low for steam

ironing.

Set an ironing temperature that is

suitable for steam ironing ( 2 to

MAX). Put the iron on its heel and

wait until the temperature light goes

out before you start ironing.

Water drips

from the

soleplate after

the iron has

cooled down or

has been stored

(specic types

only).

You have put the iron

in horizontal position

while there was still

water in the water

tank.

Empty the water tank and set the

steam control to position O after use.

Store the iron on its heel.

4239.000.6145.8

3/9

Philips gc2505 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info