Bedienungsanleitung Philips VR110 (Seite 27 von 39) (Englisch)

54447

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

— 28 —

• Frequent still, frame-by-frame and slow-

motion playback may damage the tape

and cause picture degradation.

• With some tapes, better picture quality

may not be obtained even with S-VHS ET

recording. It is recommended that you do

test record beforehand to make sure

whether better results can be obtained.

• High Grade tapes are recommended for

superior results.

• If the playback picture becomes blurred

or interrupted, use a cleaning cassette.

EasyLink Functions

When you connect the VCR and TV

equipped with T-V Link, EasyLink,

MegaLogic, SMARTLINK, Q-Link,

DATA LOGIC, or NEXTVIEWLINK via

fully-wired 21-pin SCART cable (✈P.8),

the following functions are available.

• Direct Recording

• NextView Link

• TV Auto Power ON

• VCR Auto Standby

For details, refer to the instructons

manual for your TV.

The degree of compatibility and

available functions may differ your

system.

Direct Recording

You can start recording the programme

that you are watching on your TV with

simple operation. Follow the procedure

below to use this function.

1 Press VCR.

2 Press MENU.

3 Press 5 or ∞ to select “VCR SET

UP” then press OK/STATUS.

4 Press 5 or ∞ to select “DIRECT

REC” then press 3 to set to “ON”.

5 Press MENU to exit the menu

operation.

6 Press REC/OTR ¶. The VCR will

record the programme you currently

watch.

• If “DIRECT REC” is set to

“OFF”, the REC/OTR ¶ button

functions as described in

“Recording”. (✈P.22)

• During the Direct Recording

“CH

_ _

” appears on the display

panel.

DVANCE

PERATION

(CONTINUED)

Automatic Satellite Programme

Recording

This facility allows you to record

automatically a satellite programme

which is timer-programmed on your

external satellite tuner. Connect a

satellite tuner to the VCR’s AV2 (L-2)

IN/DECODER connector (✈P.8) and

programme the timer on the satellite

tuner; the VCR starts recording when it

signals input from the satellite tuner to

the AV2 (L-2) IN/DECODER connec-

tor, and when there is no input signal

the VCR stops recording and the power

shuts off.

Before performing the following steps:

• Make sure the satellite tuner is

connected to the VCR’s AV2 (L-2)

IN/DECODER connector. (P.8)

• Programme the timer on the satellite

tuner.

• Insert a cassette with the safety tab

in place.

1 Press VCR.

2 Press MENU.

3 Press 5 or ∞ to select “VCR SET

UP” then press OK/STATUS.

4 Press 5 or ∞ to select “AUTO SAT

RECORD LINK”.

5 Press 4 to set to “ON”.

6 Press MENU.

The following message will appear.

Press POWER to turn off the VCR. If

you do not turn off the VCR after 30

seconds, the VCR will turn off

automatically.

The VCR will then move to stand-by

mode and “L-2” will blink on the

display panel.

Notes:

• Pressing the POWER or STAND/BY

button while Automatic Satellite

Programme Recording mode or stand-by

mode is in progress will cancel the mode

and "AUTO SAT RECORD LINK" is set

back to "OFF" automatically.

• Be sure not to turn on the satellite tuner

before the program is executed otherwise

the VCR will start recording when the

satellite tuner's power is turned on.

• Depending on the type of satellite tuner,

the VCR may not record a slight portion

of the beginning of the programme or may

record slightly longer than the actual

length of the programme.

• While the VCR is in Automatic Satellite

Programme Recording or stand-by mode,

normal timer recording will not perform.

•“Err L-2” will appear if you engage the

Automatic Satellite Programme

Recording while the satellite tuner power

is on. Turn off the satellite tuner.

However, if “Err” will not disappear even

though the satellite tuner is turned off,

Automatic Satellite Programme

Recording function will not work properly

with that satellite tuner.

S-VHS ET

This VCR allows recording in Super VHS

ET (Expansion Technology) mode. You

can record with S-VHS picture quality

on VHS cassettes. However, this funcion

is available only for SP recording.

1Select S-VHS ET Mode

1 Press the S-VHS ET button on the

front panel to select S-VHS ET

recording mode before recording.

The lamp will lit.

2 Press the button again to cancel

S-VHS ET recording mode after

recording.

Notes:

•“S-VHS ET” setting cannot be changed

during recording, timer recording, or

when the VCR’s power is off.

Also, this function dows not work with

S-VHS tapes.

• To obtain the highest quality recording

and playback pictures over a longer

period on this model, S-VHS recording

on S-VHS tape is recommended.

• You can playback S-VHS ET recordings

not only on this VCR but also on another

VCR equipped with S-VHS ET.

• It is recommended to specifically label

S-VHS ET recordings so you can easily

distinguish them from regular VHS

recordings.

• S-VHS ET recordings can also be played

back on an S-VHS VCR. However, there

may be cases where S-VHS ET playback

is not possible on a particular VCR.

DSPC ON

O. S. D. ON

\DIRECT REC ON

AUTO SP=LP TIMER OFF

DIGITAL 3R ON

POWER SAVE OFF

AUTO SAT

RECORD LINK OFF

SELECT : 5∞ CHANGE :4

END : MENU

PLEASE FOLLOW THE STEPS

BELOW:

1 SET PROGRAM ON SAT

2 TURN SAT OFF

3 TURN VCR OFF

Untitled-2 16/08/2000, 15:3828

Philips VR110 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips VR110

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info