Bedienungsanleitung Piazzetta P960 (Seite 12 von 64) (Englisch)

643476

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

In determining optimum vent termination, carefully evaluate external

conditions especially when venting directly through a wall. Since you

must deal with odors, gases, and y ash, consider aesthetics, prevailing

winds, distances from air inlets and combustibles, location of adjacent

structures and any code requirements.

•Exhaust must terminate above combustion air inlet elevation.

•Do not terminate vent in any enclosed or semi-enclosed area, (i.e.

Carports, garage, attic crawl space, etc.) or any location that can build

up a concentration of fumes.

•Terminals must not to be recessed into a wall or siding.

•When setting into place ue caps you should consider wind factors

such as dominate wind directions and currents in order to avoid down

draft, y ash and/or smoke.

a Vent surfaces can get hot enough to cause burns if touched

by children.

Non-combustible shielding or guards may be required.

a Be sure to use approved pellet vent pipe and wall pass-

through ttings to go through combustible materials.

The type of installation must rst be considered before determining

the exact location of the venting termination in relation ship to doors,

window, cavities or air vents. See gures 18-19.

Without outside combustion air connected to the unit.

For These types of installations please refer to the dimensions listed in

gure 18.

The clearance to a door, window or cavity must be at least:

- 4’ (1.2 m) below;

- 4’ (1.2 m) horizontally;

- 1’ (305 mm) above.

The clearance to fresh air intake for combustion of the pellet stove

or any other appliance, or the non-mechanical air supply inlet to the

building must be at least 4’ (1.2 m).

The clearance to a mechanical air supply inlet to the building must be

at least 10’ (3 m).

With outside combustion air connected to the unit.

For These types of installations please refer to the dimensions listed in

gure 19.

DT0000000-00

1.12 vENTING: TERMINATION REqUIREMENTS

FRESH AIR

INTAKE

MECHANICAL

AIR SUPPLY INLET

4' 10'

A = EXHAUST TERMINAL

1,5'

FRESH AIR

INTAKE

MECHANICAL

AIR SUPPLY

INLET

A = EXHAUST TERMINAL

Fig. 18

Fig. 19

This conguration will help prevent blockage of vent by snow drifts. Also the minimum vertical run of 5 feet (1,5 m) ensures the ventilation of the

exhaust in the event of a power failure, and allow for easier cleaning through cleanout on tee.

a Certain local code restrictions may apply. Check with Local Ofcials rst before installing.

a Strictly observe the PL Vent manufacturer’s safety specications when using wall pass through.

a INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.

a Double wall PL vent requires a minimum clearance to combustibles according to the manufacturer’s safety specications and the use

of listed wall thimble, re stop or roof ashing where applicable.

a Do not place joints within wall pass-throughs.

a Ensure that all installation work is carried out to professional standards.

H07028100/DT2000970 – 01

English

DT2033048-00

DT2033047-00

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Piazzetta P960 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info