Bedienungsanleitung Piazzetta P960 (Seite 20 von 64) (Englisch)

643476

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Pursuant to current regulations on the safety of electrical equipment, you must contact your dealer or a qualied electrician for all and any work

connected with installation, maintenance or servicing that involves access to electrical parts.

Cladding

•Having completed assembly of the stove and installed any external room thermostat, proceed with assembly of the stove cladding, referring to the

ceramic cladding instruction booklet provided with the stove.

5.0 INSTALLATION

•Thanks to Piazzetta technology and R&D, this pellet stove offers the

advantages of the “Multifuoco system”, a system EXCLUSIVE to and

PATENTED by Gruppo Piazzetta S.p.A., a true innovation in the eld of

pellet stoves.

•The “Multifuoco system” revolutionises all methods of heat circulation

currently in use in pellet stoves: the heat produced by the rebox is

not only circulated from the lower part of the stove into the room, but

hot air can also be ducted via Ø 3” / (Ø 75 mm) hoses to adjoining

rooms (Fig. 25).

This exclusive oor-standing heat distribution system offers notable

advantages: even spread of temperatures (Fig. 24).

The hot air produced is propelled by two fans and distributed via the

grille at the back of the stove.

•The front grill is equipped with two deectors (Fig. 26) to change the

direction of the heat current as it exits the front of the stove. To deect

the heat current in the desired direction simply adjust the angle of the

deectors (Fig. 27) using the lever provided (Fig. 28).

Instructions for ducting the hot air

•The fan kit, which propels hot air into the room, can be tted with two

Y-elements (one for each motor) which effectively allow the hot air

ow to be doubled up, directing it via a hose also to the rear of the

stove, from where it can then be ducted to adjoining rooms.

a Do not install more than two Y-elements in the stove otherwise

there could be problems of overheating.

•Some examples of possible installation are given below as well as

examples of how to duct the hot air in order to heat other rooms. Such

examples are given purely for demonstration purposes; best efciency

can be obtained using Ø 3” / (Ø 75 mm) coated ducting in accordance

with instructions given in the sub-paragraph “Wall and oor ducting”

and with a maximum total hose length of 32.8’ / (10 m).

This length consists of the sum of the single lengths of hoses for each

fan.

a It is of fundamental importance that when ducting heat from

the rear of the stove, the outlet vents near the stove or the

Y-element must not be closed in order to avoid overheating.

In cases where only one rear outlet from the fan is envisaged,

the outlet vent must always be kept open.

DT2010145-04

5.1 MULTIFUOCO SySTEM

Fig. 24

Fig. 25

Fig. 26

Deﬂectors

Fig. 27 Fig. 28

H07028100/DT2000970 – 01

English

DT2010144-02

DT2010071-05

DT2030163-00

DT2030162-00

DT2030610-01

DT2030221-01 DT2030223-01

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Piazzetta P960 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info