Bedienungsanleitung Pioneer AVH-X2800BT (Seite 41 von 57) (Englisch)

649371

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

remove them in advance. Surrounding sounds may prevent

correct measurement of the vehicle’s acoustics.



Be sure to use the microphone for acoustical measurement

(sold separately). Using another microphone may prevent

measurement, or result in incorrect measurement of the

vehicle’s acoustics.



To perform Auto EQ, the front speakers must be connected.

 When this product is connected to a power amp with input

level control, Auto EQ may be impossible if the power amp’s

input level is set below the standard level.



When this product is connected to a power amp with an LPF

(low pass filter), turn the LPF off before performing Auto EQ.

Also, set the cut-off frequency for the built-in LPF of an active

subwoofer to the highest frequency.



The distance has been calculated by a computer to provide

optimum delay to ensure accurate results. Do not change

this value.

— The reflected sound within the vehicle is strong and delays

occur.

— The LPF on active subwoofers or external amps delay the

lower sounds.



If an error occurs during measurement, check the following

before measuring the vehicle’s acoustics.

— Front speakers (left/right)

— Rear speakers (left/right)

— Noise

— Microphone for acoustical measurement (sold separately)

— Low battery

Performing Auto EQ

p Auto EQ changes the audio settings as follows:

— The fader/balance settings return to the centre position.

 Refer to Using fader/balance adjustment on page 38

— “Mute Level” is set to “Off”.



Refer to Switching sound muting/attenuation on page 38

Previous settings for Auto EQ will be overwritten.

CAUTION

Do not turn off the engine while the measurement is in

progress.

1 Stop the vehicle in a quiet place, close all the

doors, windows and sun roof, and then turn the

engine off.

If the engine is left running, engine noise may prevent correct

Auto EQ.

If driving restrictions are detected during measurement,

measurement is cancelled.

2 Fix the microphone for acoustical measurement

(sold separately) in the centre of the headrest

of the driver’s seat, facing forwards.

The Auto EQ may differ depending on where you place the micro-

phone. If desired, place the microphone on the front passenger

seat and perform Auto EQ.

3 Disconnect the iPhone or smartphone device.

4 Turn on the ignition switch (ACC ON).

If the vehicle’s air conditioner or heater is turned on, turn it off.

5 Switch the AV source to “Source OFF”.

 Refer to Selecting a source on page 9

6 Display the “Audio” setting screen.

 Refer to Displaying the “Audio” setting screen on page 38

7 Touch [A-EQ&TA Measurement].

The “A-EQ&TA Measurement” screen appears.

8 Connect the microphone for acoustical meas-

urement (sold separately) with this product.

Plug the microphone into the AUX input jack on this product.

Use an extension cable (sold separately) if the cord of the

Microphone (sold separately) is not long enough.

9 Touch [Front Left] or [Front Right] to select the

current listening position.

10 Touch [Start].

A 10-second countdown starts.

The Bluetooth connection is disconnected before the pro-

cess starts.

11 Exit the vehicle and keep the doors closed until

the countdown finishes.

When the countdown finishes, a measurement tone (noise)

is emitted from the speakers and the Auto EQ measurement

begins.

12 Wait until the measurement is completed.

When Auto EQ is completed, a message is displayed.

The measurement time varies depending on the type of

vehicle.

 To stop the measurement, touch [Stop].

13 Store the microphone carefully in the glove box

or another safe place.

If the microphone is subjected to direct sunlight for an extended

period, high temperatures may cause distortion, colour change

or malfunction.

Saving the sound settings

You can save to recall the following current sound settings:

bass boost, slope, subwoofer phase, speaker level, Graphic EQ,

HPF/LPF, listening position, crossover, time alignment.

1 Display the “Audio” setting screen.

 Refer to Displaying the “Audio” setting screen on page 38

2 Touch [Save Settings].

3 Touch [OK].

All of the current sound settings are saved.

 When you touch [Cancel], return to the “Audio”

setting screen.

Loading the sound settings

1 Display the “Audio” setting screen.

 Refer to Displaying the “Audio” setting screen on page 38

2 Touch [Load Settings].

3 Touch the item.

The following items are available:

AEQ Setting,Sound Setting.

“AEQ Setting” is available only when you have already

performed Auto EQ measurement.



Refer to Adjusting the equaliser curve automatically (Auto EQ)

on page 40

“Sound Setting” is available only when you have already

saved the sound settings.



Refer to Saving the sound settings on page 41

< CRB4721-B >

Audio adjustments

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVH-X2800BT Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer AVH-X2800BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info