Bedienungsanleitung Pioneer AVIC-HD3 II (Seite 134 von 193) (Englisch)

491808

134

Zoom out

Zoom in

Vorherige Seite

1/193

Nächste Seite

Camera for Rear view mode

[Rear View] can be displayed at all times (e.g.

when monitoring an attached trailer, etc.) as a

split screen where map information is partially

displayed. Please be aware that in this setting,

camera image is not resized to fit, and that a

portion of what is seen by the camera is not

viewable.

CAUTION

Pioneer recommends the use of a camera which

outputs mirror reversed images, otherwise screen

image may appear reversed.

p Immediately confirm whether the display

changes to a rear view camera image when

the gearstick is moved to REVERSE (R)

from another position.

p When the screen changes to full-screen

rear view camera image during normal

driving, switch to the opposite setting in

[Polarity].

p Initially, this function is set to [Off].

1 Touch [Camera Input] in

System Settings menu.

2 Touch [On] to turn rear view camera

setting on.

p Unless this setting is [On], you cannot

switch to Rear View mode.

3 Touch [Polarity] to select an appropriate

setting for polarity.

Each time you touch [Polarity] switches be-

tween the following polarity:

! Battery — When the polarity of the con-

nected lead is positive while the gearstick is

in the REVERSE (R) position

! GND — When the polarity of the connected

lead is negative while the gearstick is in the

REVERSE (R) position

Setting the video input

You can switch the setting according to the

connected component.

p Select [Video] to watch video of a con-

nected component as AV INPUT source.

% Touch [AV Input] in System Settings

menu.

Each touch of [AV Input] changes the set-

tings as follows:

! Off — No video component is connected

! Video — External video component

! EXT — Pioneer external unit connected

with an RCA video cable

p When a Pioneer external unit is connected

with an IP-BUS cable, select [EXT]. When

the audio source is [EXT], the “Video

image” of the Pioneer external unit can be

displayed.

Switching the auxiliary setting

It is possible to use auxiliary equipment with

the navigation system as the one of sources.

Activate the auxiliary setting when using aux-

iliary equipment connected to the navigation

system.

% Touch [AUX Input] in System Settings

menu.

Touching [AUX Input] switches between [On]

and [Off].

= For details, refer to Selecting [AUX] as the

source on page 125

Switching the muting/

attenuation timing

You can mute the audio source volume or at-

tenuate the output signal. This setting is inva-

lid for the mute signal has been received from

the MUTE lead connected to the navigation

unit. (Even if this setting is [Off], the naviga-

tion system will mute or attenuate the audio

source volume when the signal is output via

MUTE lead.)

Customising the Audio Setting related with Audio Visual

Engb

134

Chapter

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVIC-HD3 II Seite 134

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer AVIC-HD3 II

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info