Bedienungsanleitung Pioneer AVIC-HD3 II (Seite 162 von 193) (Englisch)

491808

162

Zoom out

Zoom in

Vorherige Seite

1/193

Nächste Seite

Messages and How to React to Them

The following messages may be displayed by your navigation system.

p There are occasions when you may see

error messages other than those shown

here. In such a case, follow the instructions

given on the display.

Messages for navigation functions

Message When What to do (See)

Irregular speed pulse signal

detected. Please power off

the system and check the in-

stallation. Then, please re-

boot the system and press

“OK”.

If the Navigation system does not re-

ceive the vehicle speed pulse.

Consult your Pioneer dealer.

Speed pulse not connected.

Calibration will start without

speed pulse. Accuracy is not

fully ensured without speed

pulse.

The speed signal input (pink lead

wire) of the power cable is not con-

nected.

To operate with 3D hybrid mode, connect the

speed signal input (pink lead wire) of the

power cable correctly.

Although it can be operated with Simple hy-

brid mode without connecting the speed sig-

nal input, the precision of the positioning will

be less accurate.

Vibration detected. Please

power off the system and

check the installation. Then,

please re-boot the system and

press “OK”.

The navigation unit is installed in a

place where it may be affected by a

large vibration.

Re-install the navigation unit in a place where

the unit will not be affected by vibration.

Direction of G sensor is not

correct. Please power off the

system and check the installa-

tion. Then, please re-boot the

system and press “OK”.

Direction of G sensor is set incor-

rectly.

See the Installation Manual and set the direc-

tion of the navigation unit correctly.

Gyro Sensor is not working

properly. Please consult your

dealer or Pioneer service cen-

tre.

Abnormal Gyrosensor output is de-

tected.

Write down the error code shown on the

screen. Turn off the power, and then contact

your nearest Pioneer service facility.

Positioning is not possible

due to the hardware. Please

contact your dealer or Pioneer

service centre.

The location display is not possible

due to hardw are failure.

Consult your dealer.

GPS antenna problem de-

tected. Please contact your

dealer or Pioneer service cen-

tre.

The location display is not possible

due to failu re of the GPS aerial.

Consult your dealer.

This function is currently una-

vailable.

The screen cannot be displayed with

Vehicle Dynamics Display. The sen-

sor has not been taught so the sen-

sor information cannot be acquired.

If the sensor learning status reaches the Sen-

sor Initialising, the system is ready to be

used.

The vertical installation angle

is changed. Gyro Sensor cali-

bration is re-initialized.

If the mounting angle of the naviga-

tion unit has been changed.

The system initialises the sensor in order to

operate it with the maximum performance

and automatically starts re-learning.

Appendix

Engb

162

Appendix

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVIC-HD3 II Seite 162

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer AVIC-HD3 II

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info