Bedienungsanleitung Pioneer AVIC-X3 (Seite 139 von 164) (Englisch)

62771

139

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

137

AppendixNAVI/AV

Problems in the audio screen (during iPod playback)

Messages and how to react to them

The following messages may be displayed by your navigation system.

❒ There are occasions when you may see error messages other than those shown here. In such a

case, follow the instructions given on the display.

Symptom Cause Action (See)

Cannot be operated. The iPod is frozen. Reconnect the iPod with the inter-

face cable for iPod

(sold sepa-

rately).

The authorisation error has occurred. • Reconnect the iPod with the inter-

face cable for iPod

(sold sepa-

rately).

• Set the ACC to Off and set it to On

again.

• Update the iPod version.

Message When What to do

Please insert the appropriate disc.

This is not the appropriate disc.

Please insert the appropriate disc.

If you try to use a disc which is

incompatible with this system.

Insert a suitable disc.

If you insert a disc upside down. Insert the disc with the label upward.

If the disc is dirty. Clean the disc.

If the disc is cracked or otherwise

damaged.

Insert a normal, round disc.

Irregular speed pulse signal is

detected. Please turn system power

off and check the installation. After

checking, please re-boot the system

and press “OK”.

If the Navigation system does not

receive the vehicle speed pulse.

Consult your Pioneer dealer.

Speed pulse wire is not connected.

Please be sure to connect the system

to the speed pulse wire. Accuracy is

not fully ensured without speed

pulse.

The speed signal input (pink lead

wire) of the power cable is not con-

nected.

To operate with 3D hybrid mode, con-

nect the speed signal input (pink

lead wire) of the power cable cor-

rectly.

Although it can be operated with

Simple hybrid mode without con-

necting the speed signal input, the

precision of the positioning will be

less accurate.

Vibration is detected. Please turn

system power off and check the

installation. After checking, please

re-boot the system and press “OK”.

The navigation unit is installed in a

place where it may be affected by a

large vibration.

Re-install the navigation unit in a

place where the unit will not be

affected by vibration.

Direction of G sensor is not correct.

Please turn system power off and

check the installation. After check-

ing, please re-boot the system and

press “OK”.

Direction of G sensor is set incor-

rectly.

See the “Installation Manual” and set

the direction of the navigation unit

correctly.

Gyro Sensor is not working properly.

Please consult your dealer or Pioneer

service centre.

Abnormal output is detected from

the Gyrosensor.

Note down the error code shown on

the screen. Turn off the power, and

then contact your nearest Pioneer

service facility.

This function is not available now. The screen cannot be displayed with

Vehicle Dynamics Display.

Because the sensor has not been

taught so the sensor information

cannot be acquired.

If the sensor learning status reaches

the Sensor Initialising status, the sys-

tem is ready to be used.

MAN-AVIC-X3-EN.book Page 137 Wednesday, June 6, 2007 10:15 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVIC-X3 Seite 139

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer AVIC-X3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info