Bedienungsanleitung Pioneer AVIC-X3 (Seite 140 von 164) (Englisch)

62771

140

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

138

Appendix NAVI/AV

System detected that the vertical

angle of the installation has been

changed. Learning status for Gyro

Sensor has been initialised.

If the mounting angle of the naviga-

tion unit has been changed.

The system initialises the sensor in

order to operate it with the maximum

performance and automatically

starts re-learning.

System detected that the vertical

angle of the installation exceeds the

permission level. Please install the

navigation unit correctly.

The navigation system is installed

with an extreme angle exceeding the

limitation of the installation angle.

Confirm the installation angle. (The

navigation system must be installed

within the allowed installation angle.

For details refer to Installation Man-

ual.)

Route calculation was not possible. Route calculation has failed because

of a malfunction of map data, soft-

ware, hardware or disc.

• Change the destination.

•Clean the disc.

• Consult the Pioneer Local dealer if

this message persists.

Route calculation was not possible

because the destination is too far.

The destination is too far. • Set a destination closer to the start-

ing point.

• Set one or more way points.

Route calculation was not possible

because the destination is too near.

The destination or way point(s) are

too close.

Set a destination or way point(s) far-

ther from the starting point.

Route calculation was not possible

due to traffic regulations.

• The destination or way point(s) are

in a Control Traffic Zone (CTR) and

the route calculation is hampered.

• Your vehicle is currently in a Con-

trol Traffic Zone (CTR) and the

route calculation is hampered.

• Set a destination and way point(s)

outside the CTR if you know where

the restricted area is.

• Try a destination or way point(s)

away from the currently set points

to some extent.

• Drive your vehicle to an unre-

stricted area and reset the destina-

tion and way point(s).

Route calculation was not possible

because no guidance can be pro-

vided around the destination or the

starting point.

The destination, way point(s) or start-

ing point are in an area where no

road exists (e.g. a mountain) and the

route calculation is impossible.

• Set a destination and way point(s)

on roads.

• Reset the destination after you

drive the vehicle to any road.

There is no route to the destination. The destination or way point(s) are on

an isolated island, etc. without a ferry

and the route calculation is impossi-

ble.

Change the destination.

Your journey can not avoid the speci-

fied area.

If route setting cannot avoid speci-

fied Areas to Avoid.

If the current route is not desired, set

a destination or way point(s) that do

not pass through the Areas to

Avoid.

The route could not avoid the speci-

fied area.

Toll road has not been avoided.

If the route to the destination or way

point(s) cannot be established by

bypassing toll roads (including toll

areas) and Areas to Avoid.

If the current route is not desired, set

a destination or way point(s) that do

not pass through toll roads (includ-

ing toll areas) and Areas to Avoid.

Ferry has not been avoided. In case a ferry route was included in

the route to the destination or way

point(s) even though “Avoid Ferry”

was set to On.

If the current route is not desired, set

a destination or way point(s) that do

not pass through a ferry route.

Toll road has not been avoided. If the route to the destination or way

point(s) cannot be established by

bypassing toll roads (including toll

areas).

If the current route is not desired, set

a destination or way point(s) that do

not pass through toll roads (includ-

ing toll areas).

There is no applicable data for the

selected city. Automatically returning

to list.

If the history data of the city could

not be used (for example, if the his-

tory data of the city that was used in

the POI Search cannot be found in

the Address Search.)

Once the search is performed to

specify the city, the result is saved as

a history. The data of the specified

city, however, may not be hit by the

different search criteria. In this case,

try another search method or change

the destination.

There is no Motorway in this area. If no motorway was found in the

selected country.

Set the destination or way points

using another search method or

change the location of the destina-

tion or way point(s).

Message When What to do

MAN-AVIC-X3-EN.book Page 138 Wednesday, June 6, 2007 10:15 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVIC-X3 Seite 140

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer AVIC-X3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info