Bedienungsanleitung Pioneer CNDV-50MT (Seite 120 von 142) (Englisch)

454962

120

Zoom out

Zoom in

Vorherige Seite

1/142

Nächste Seite

118

Appendix NAVI/AV

Your vehicle is operating in Simple

hybrid mode.

Connect the speed signal input (pink

lead wire) of the power cable

correctly, and reset the 3D Hybrid

Sensor memory (“Learning

Status”).

The navigation unit is installed with

an extreme angle exceeding the

limitation of the installation angle.

Confirm the installation angle. (This

unit must be installed within +30

degrees to –30 degrees of the

horizontal, or within five degrees of

your vehicle’s direction of travel.)

Indication of the position of your

vehicle is misaligned after a U-turn or

reversing.

Check whether or not the reverse

gear signal input lead (purple) is

connected properly. (The Navigation

System works properly without the

lead connected, but positioning

accuracy will be adversely affected.)

The map continually reorients itself. The travelling direction is always set

to north.

Touch on the screen and change

the map display.

Tracking marks are not displayed. The “Tracking Display” is turned

off.

Check the “Tracking Display”

settings (

➞ Page 57) and make sure

“Always” or “This Trip” is selected.

The daylight display is used even

when the vehicle lights are on.

Daytime is selected on “Day/Night

Display”.

Check the “Day/Night Display”

setting (

➞ Page 58) and make sure

“Illuminated” is selected.

The Orange/white lead is not

connected.

Check the connection.

The system will not switch on or will

not operate.

Installation or connection has been

carried out incorrectly.

Check with your dealer.

The display is very dim. The vehicle’s light is turned ON, and

“Illuminated” is selected on “Day/

Night Display”.

Read about the “Day/Night

Display” setting (

➞ Page 58) and, if

desired, select “Daytime”.

The vehicle cabin temperature is

extremely low.

A Liquid Crystal Display (LCD) is

used, and such displays tend to

darken when cold. Wait for the

vehicle to warm up.

Picture quality adjustment of the

display is not correct.

Refer to “Hardware Manual” to adjust

the picture quality.

Ambient light sensor of the display is

hidden.

Set the ambient light sensor not to

be hidden.

There is no voice guidance or the

volume is low.

The volume setting is low or the

speaker lead is disconnected.

Check the volume setting on the

display or turn the volume up

according to “Volume” (

➞ Page 55)

and/or turn up the volume on the

display.

Slope is not displayed on the

Vehicle Dynamics screen.

Inclination does not move on the 3D

Calibration Status screen.

The speed pulse lead is not

connected.

Connect the speed pulse lead.

When the screen is frozen...

Park your vehicle at a safe place, and cut the engine off. Turn the ignition key back to “Acc off”. Then

start the engine again, and turn the power to the navigation unit back on. If this does not solve the

problem, press the RESET button on the navigation unit.

Symptom Cause Action (See)

MAN-CNDV-50MT-EN.book Page 118 Wednesday, May 4, 2005 1:49 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer CNDV-50MT Seite 120

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer CNDV-50MT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info