Bedienungsanleitung Pioneer DJM-350-W (Seite 10 von 116) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

491997

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

DRB1501-D

— [ ]: Set here for a curve that rises steeply. (When the cross-

fader moves away from either the left or right edge, the sound

is immediately output from the opposite side.)

5 Move the crossfader j.

Switch the channel whose sound is output from the speakers.

— Left edge: The [CH-1] sound is output.

— Center position: The sound of [CH-1] and [CH-2] is mixed and

output.

— Right edge: The [CH-2] sound is output.

! This operation is not necessary when the [THRU,

, ] (cross-

fader curve selector) switch is set to [THRU].

6 Turn [MASTER LEVEL] 2 clockwise.

Sound is output from the speakers.

The master level indicator e on the control panel lights.

Adjust [MASTER LEVEL] so that the orange indicator lights at the point

in the track where the volume is loudest (the climax, etc.).

Be careful that the red indicator does not light, or the sound could be

distorted.

Adjusting the sound quality

Turn the [CH-1] 1 or [CH-2] 2 [HI], [MID] or [LOW] d

control.

Refer to Specifications on page 16 for the range of sound that can be

adjusted by each control.

! The sound for that range can be turned completely off by turning

the control all the way counterclockwise (isolator function).

Mixing using the faders

Prepare the unit in advance so that the sound of [CH-1] 1 is being out-

put from the speakers. For instructions on preparation, see Outputting

sound on page 9.

For instructions on monitoring the sound, see Monitoring the sound

over headphones (headphones section) on page 11.

 Mixing using the channel faders

1 Set [THRU,

, ] (the crossfader curve selection

switch) i to [THRU].

2 Switch the [CD, PHONO] (input selector) switch b for

the [CH-2] 2.

3 Turn the [TRIM] c control for the [CH-2] 2 clockwise.

4 Press [CH-2 CUE] 7.

The sound of [CH-2] is monitored from the headphones.

5 Turn [MIXING] 8.

This adjusts the balance of the monitor volume between the sound

output from the [MASTER OUT 1, 2] terminals (the sound of [CH-1])

and the sound of [CH-2].

6 Operate the DJ player connected to the [CH-2]

terminals.

While checking the sound over the headphones, adjust the tempo of

[CH-2] track to match the tempo of [CH-1] track.

7 While moving the [CH-2] 2 channel fader to the back,

move the [CH-1] 1 channel fader to the front.

While checking the sound output from the speakers, operate the chan-

nel faders to substitute the sound of [CH-1] with the sound of [CH-2].

Mixing is completed once only the [CH-2] sound is being output from

the speakers.

 Mixing using the crossfader

1 Set [THRU,

, ] (the crossfader curve selector

switch) i to [ ] or [ ].

2 Operate [CH-2] 2.

Operate as described in steps 2 to 6 under Mixing using the channel

faders on page 10.

3 Move the crossfader j gradually to the right.

While checking the sound output from the speakers, operate the

crossfader to substitute the sound of [CH-1] with the sound of [CH-2].

Mixing is completed once only the [CH-2] sound is being output from

the speakers.

Using the fader to play a Pioneer DJ

player (fader start)

If you connect a Pioneer DJ player using a control cable (supplied with

a DJ player), you can start playback of control other operations of the

DJ player with the fader of this unit.

The fader start function can only be used when connected to a Pioneer

DJ player.

Connect this unit and Pioneer DJ player beforehand. For instructions

on connections, see Connecting the input/

output terminals on page 7.

 To start playback using the channel faders

1 Set [THRU,

, ] (the crossfader curve selection

switch) i to [THRU].

2 Press [FADER START] h.

Turn the fader start function on.

3 Move the channel fader g all the way to the front.

4 Set the cue on the DJ player.

The DJ player pauses playback at the cue point.

5 Move the channel fader g to the back.

Playback starts on the DJ player.

! If you set the channel fader back to the original position, the player

instantaneously returns to the cue point already set and pauses

playback (back cue).

 To start playback using the crossfader

1 Set [THRU,

, ] (the crossfader curve selector

switch) i to [ ] or [ ].

2 Press [FADER START] h.

Turn the fader start function on.

3 Move the crossfader j.

Move the crossfader to the opposite edge from the channel for which

you want to use the fader start function.

4 Set the cue on the DJ player.

The DJ player pauses playback at the cue point.

5 Move the crossfader j.

Playback starts on the DJ player.

! If you set the crossfader back to the original position, the player

instantaneously returns to the cue point already set and pauses

playback (back cue).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer DJM-350-W Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info