Bedienungsanleitung Pioneer SC-1223 (Seite 97 von 119) (Englisch)

536834

Zoom out

Zoom in

Vorherige Seite

1/119

Nächste Seite

FAQ

ADAPTER PORT terminal

Symptom Remedy

The Bluetooth wireless technology

device cannot be connected or oper-

ated. Sound from the Bluetooth wire-

less technology device is not emitted

or the sound is interrupted.

Check that no object that emits electromagnetic waves in the 2.4 GHz band (microwave

oven, wireless LAN device or Bluetooth wireless technology apparatus) is near the unit. If

such an object is near the unit, set the unit far from it. Or, stop using the object emitting

the electromagnetic waves.

Check that the Bluetooth wireless technology device is not too far from the unit and that

obstructions are not set between the Bluetooth wireless technology device and the unit.

Set the Bluetooth wireless technology device and the unit so that the distance between

them is less than about 10 m and no obstructions exist between them.

Check that the Bluetooth ADAPTER and the ADAPTER PORT of the unit are correctly

connected.

The Bluetooth wireless technology device may not be set to the communication mode

supporting the Bluetooth wireless technology. Check the setting of the Bluetooth wireless

technology device.

Check that pairing is correct. The pairing setting was deleted from this unit or the Blue-

tooth wireless technology device. Reset the pairing.

Check that the profile is correct. Use a Bluetooth wireless technology device that supports

A2DP profile and AVRCP profile.

The Air Jam function cannot be

used.

Disconnect the iPod from this receiver (see Air Jam on page 49).

Video

Symptom Remedy

No image is output when an input is

selected.

Check the video connections of the source component.

For HDMI, or when V.CONV is set to OFF and a TV and another component are con-

nected with different cords (in Setting the Video options on page 67), you must connect

your TV to this receiver using the same type of video cable as you used to connect your

video component. For the component video input, however, signals are only output from

the HDMI OUT 1 terminal, so when using the component video input, set V.CONV to ON.

Make sure the input assignment is correct for components connected using component

video or HDMI cables (see The Input Setup menu on page 38).

Check the video output settings of the source component.

Check that the video input you selected on your TV is correct.

Some components (such as video game units) have resolutions that may not be con-

verted. If adjusting this receiver’s Resolution setting (in Setting the Video options on page

67) and/or the resolution settings on your component or display doesn’t work, try switch-

ing V.CONV (in Setting the Video options on page 67) to OFF.

When the device is connected using an HDMI OUT terminal, press the remote control’s

HDMI OUT button to check the HDMI OUT output setting. For OUT 2, also check the

MAIN/HDZONE setting at ZONE Setup.

Can’t record video. Check that the source is not copy-protected.

The video converter is not available when making recordings. Check that the same type

of video cable is used for connecting both the recorder and the video source (the one you

want to record) to this receiver.

Symptom Remedy

Noisy, intermittent, or distorted

picture.

Sometimes a video deck may output a noisy video signal (during scanning, for example),

or the video quality may just be poor (with some video game units, for example). The

picture quality may also depend on the settings, etc. of your display device. Switch off

the video converter and reconnect the source and display device using the same type of

connection (component or composite), then start playback again.

Video signals are not output from the

component terminal.

When a monitor only compatible with resolutions of 480i is connected to the component

terminal and another monitor is connected to the HDMI terminal, the video signals may

not be output to the monitor connected to the component terminal. If this happens, do

the following:

— Turn off the power of the monitor connected to the HDMI terminal.

— Change the VIDEO PARAMETER menu RES setting (see Setting the Video options on

page 67).

— Video signals from the HDMI terminal cannot be output to the component terminals.

Input the video signals from the player or other source to the composite or component

terminals. When using the component terminal, assign it at Input Setup (see The Input

Setup menu on page 38).

The picture's movement is unnatural.

When Resolution under VIDEO PARAMETER is set to 1080/24p, the picture may not be

displayed properly for some source materials. In this case, set the resolution to some-

thing other than 1080/24p (page 67).

Settings

Symptom Remedy

The Auto MCACC Setup continually

shows an error.

The ambient noise level may be too high. Keep the noise level in the room as low as

possible (see also Problems when using the Auto MCACC Setup on page 38). If the noise

level cannot be kept low enough, you will have to set up the surround sound manually

(page 86).

When using only one surround back speaker, connect it to the SURROUND BACK L

(Single) terminals.

To use a 5.1-channel speaker set, use the surround speakers for the surround channel,

not the surround back channel.

Make sure there are no obstacles between the speakers and the microphone.

If Reverse Phase is displayed, try the following:

— The speaker’s wiring (+ and –) may be inverted. Check the speaker connections.

— Depending on the type of speakers and their installation conditions, Reverse Phase

may be displayed even if the speakers are properly connected. If this happens, select

GO NEXT and continue.

— If the speaker is not pointed to the microphone (listening position) or when using

speakers that affect the phase (dipole speakers, reflective speakers, etc.), it may not be

possible to properly identify the polarity.

After using the Auto MCACC Setup,

the speaker size setting is incorrect.

There may have been some low frequency noise in the room from an air-conditioner,

motor, etc. Switch off all other appliances in the room and use Auto MCACC Setup again.

Depending on a number of factors (bass reproduction capabilities of the speakers, room

size, speaker placement, etc.) this may occur in some cases. Change the speaker setting

manually in Speaker Setting on page 86, and use the ALL (Keep SP System) option for

the Auto MCACC menu in Automatic MCACC (Expert) on page 79 if this is a recurring

problem.

Can’t adjust the Fine Speaker Dis-

tance setting properly.

Check that the speakers are all in phase (make sure the positive (+) and negative (–)

terminals are matched up properly).

Pioneer SC-1223 Seite 97

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-1223

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info