Bedienungsanleitung Pioneer SC-1224 (Seite 104 von 126) (Englisch)

611801

104

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

104

FAQ

Symptom Remedy

When playing a disc with the listen-

ing mode set to Auto Surround or

ALC, Pro Logic II or DTS Neo:X

does not appear on the receiver.

Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on

page 56 ).

If a two channel soundtrack is currently playing (including Dolby Surround encoded),

then this is not a malfunction. Check the disc packaging for details about the audio

tracks available.

During playback of DVD-Audio, the

display shows PCM.

This will occur when playing DVD-Audio material over the HDMI connection. This is not

a malfunction.

The power turns off automatically

and some indicator flashes, or some

indicator flashes and the power does

not turn on.

See the Power section (page 100 ).

Remote control

Symptom Remedy

Cannot be remote controlled. Set the remote control unit’s remote control mode so that it matches the setting on the

main unit (see Operating multiple receivers on page 77 ).

Check whether the receiver’s remote control mode is properly set (see Remote Control

Mode Setup on page 94 ).

Try replacing the batteries in the remote control (see Loading the batteries on page 9 ).

Be sure to operate within 7 m and a 30º angle of the remote sensor on the front panel

(see Operating range of remote control unit on page 10 ).

Check that there are no obstacles between the receiver and the remote control.

Make sure that there is no fluorescent or other strong light shining on to the remote

sensor.

Other components can’t be operated

with the system remote.

If the battery ran down, the preset codes may have been cleared. Re-enter the preset

codes.

The preset code may be incorrect. Redo the procedure for entering preset codes.

When commands from the remote control units of other devices are registered using the

learning function, in some cases they may not be learned properly. In this case, register

the commands again using the learning function (see page 78 ). If they still do not work,

they may be in a special format that cannot be registered on this receiver’s remote con-

trol. Operate the device using another remote control.

HDMI

Symptom Remedy

The HDMI indicator blinks continu-

ously.

Check all the points below.

Video/audio is not output or is inter-

rupted.

This receiver is HDCP-compatible. Check that the components you are connecting are

also HDCP-compatible. If they are not, please connect them using the component or

composite video jacks.

Depending on the connected source component, it’s possible that it will not work with

this receiver (even if it is HDCP-compatible). In this case, connect using the component

or composite video jacks between source and receiver.

If the problem still persists when connecting your HDMI component directly to your

monitor, please consult the component or monitor manual or contact the manufacturer

for support.

If video images do not appear on your TV, try adjusting the resolution, Deep Color or other

setting for your component.

While analog video signals are being output over HDMI, use a separate connection for

audio output.

To output signals in Deep Color, use an HDMI cable (High Speed HDMI

Cable) to

connect this receiver to a component or TV with the Deep Color feature.

The picture and sound output get cut

off, or there is no output produced.

Influence from a TV whose power is set to standby may cause the picture or sound output

to not be produced or to get cut off. In this case, press OUT P., and make sure to use an

output other than the HDMI output to which that TV is connected.

No picture.

Try changing the Resolution setting (in Setting the Video options on page 70 ).

To use the HDMI OUT 2 terminal in the main zone, set the MAIN/HDZONE

Output Setting to MAIN (page 95 ).

No sound, or sound suddenly

ceases.

Check that the HDMI Audio setting is set to AMP (Setting the Audio options on page 68 ).

If the component is a DVI device, use a separate connection for the audio.

If analog video is being output over HDMI, please use a separate connection for the

audio.

Check the audio output settings of the source component.

HDMI format digital audio transmissions require a longer time to be recognized. Due

to this, interruption in the audio may occur when switching between audio formats or

beginning playback.

Turning on/off the device connected to this unit’s HDMI OUT terminal during playback,

or disconnecting/connecting the HDMI cable during playback, may cause noise or inter-

rupted audio.

Noisy or distorted picture. Sometimes a video deck may output a noisy video signal (during scanning, for example),

or the video quality may just be poor (with some video game units, for example). The

picture quality may also depend on the settings, etc. of your display device. Switch off

the video converter and reconnect the source and display device using the same type of

connection (component or composite), then start playback again.

If the problem still persists when connecting your HDMI component directly to your

monitor, please consult the component or monitor manual or contact the manufacturer

for support.

HDCP ERROR shows in the display. Check whether or not the connected component is compatible with HDCP. If it is not

compatible with HDCP, reconnect the source device using a different type of connection

(component or composite). Some components that are compatible with HDCP still cause

this message to be displayed, but so long as there is no problem with displaying video,

this is not a malfunction.

Pioneer SC-1224 Seite 104

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-1224

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info