Bedienungsanleitung Pioneer SC-1224 (Seite 106 von 126) (Englisch)

611801

106

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

106

FAQ

USB interface

Symptom Cause Remedy

The folders/files stored on a

USB memory device are not

displayed.

The folders/files are currently stored

in a region other than the FAT (File

Allocation Table) region.

Store the folders/files in the FAT region.

The number of levels in a folder is

more than 9.

Limit the maximum number of levels in a folder to 9 (page

47 ).

The audio files are copyrighted.

Copyrighted audio files stored on a USB memory device

cannot be played back (page 47 ).

A USB memory device is

not recognized.

The USB memory device does not

support the mass storage class

specifications.

Try using a USB memory device compatible with the mass

storage class specifications. Note that there are cases

where even the audio files stored on a USB memory device

compatible with the mass storage class specifications are

not played back on this receiver (page 47 ).

Connect the USB memory device and switch on this

receiver (page 34 ).

A USB hub is currently being used.

This receiver does not support USB hubs (page 47 ).

This receiver recognizes the USB

memory device as a fraud.

Switch off and on again this receiver.

Reconnect the USB device with the receiver switched off.

Change to an input other than iPod/USB, then set the input

back to iPod/USB.

A USB memory device is

connected and displayed,

but the audio files stored

on the USB memory device

cannot be played back.

Some formats of USB memory

devices, including FAT 12, NTFS, and

HFS, cannot be played back on this

receiver.

Check whether the format of your USB memory device is

either FAT 16 or FAT 32. Note that the FAT 12, NTFS, and

HFS formats cannot be played back on this receiver (page

47 ).

The file format cannot be properly

played back on this receiver.

See the list of file formats that can be played back on this

receiver (page 48 ).

The USB memory cannot be

operated with the remote

control.

— Press iPod USB to set the remote control to the iPod USB

control mode.

Over Current shows in the

display.

— There is a problem with the power supply for the USB

memory. After turning off the receiver, disconnect the USB

memory, connect the USB memory again and then turn on

the power of the receiver.

If Over Current is displayed even though the above opera-

tion is repeated several times, there is a problem with the

receiver or USB memory. Disconnect the power cable and

request repair.

iPod

Symptom Cause Remedy

iPod is not recognized. This receiver recognizes the iPod as

a fraud.

Switch off and on again this receiver.

Reconnect the iPod with the receiver switched off.

Change to an input other than iPod/USB, then set the input

back to iPod/USB.

iPod touch/iPhone is not

recognized or otherwise

does not operate properly.

The iPod’s operation may be

unstable.

Try performing the operation below.

1. Press the sleep/sleep cancel button on the iPod touch/

iPhone simultaneously with the home button for at least 10

seconds to restart the device.

2. Turn this receiver’s power on.

3. Connect the iPod touch/iPhone to this receiver.

iPod cannot be operated

with the remote control.

— Press iPod USB to set the remote control to the iPod USB

control mode.

Network

Symptom Cause Remedy

Cannot access the network. The LAN cable is not firmly con-

nected.

Firmly connect the LAN cable (page 33 ).

The router is not switched on. Switch on the router.

Internet security software is cur-

rently installed in the connected

component.

There are cases where a component with Internet security

software installed cannot be accessed.

The audio component on the net-

work which has been switched off is

switched on.

Switch on the audio component on the network before

switching on this receiver.

Playback does not start

while “Connecting...” con-

tinues to be displayed.

The component is currently discon-

nected from this receiver or the

power supply.

Check whether the component is properly connected to

this receiver or the power supply.

The network function can-

not be operated with the

remote control.

— Press NET to set the remote control to the network function

control mode.

The PC or Internet radio is

not properly operated.

The corresponding IP address is not

properly set.

Switch on the built-in DHCP server function of your router,

or set up the network manually according to your network

environment (page 92 ).

The IP address is being automati-

cally configured.

The automatic configuration process takes time. Please

wait.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer SC-1224 Seite 106

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-1224

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info