Bedienungsanleitung Pioneer SC-LX78-S (Seite 50 von 141) (Englisch)

580827

Zoom out

Zoom in

Vorherige Seite

1/141

Nächste Seite

Basic Setup

2 Connect the microphone to the MCACC SETUP MIC jack on the front panel.

PHONES

SPEAKERS

MULTI-ZONE

CONTROL

ZONE 2

ON/OFF

ZONE 3

ON/OFF

HDZONE

ON/OFF

MCACC

SETUP MIC

(HDMI)

HDMI 5 INPUT

AUTO/ALC/

DIRECT STATUSBAND TUNER EDIT

iPod iPhone

DIRECT CONTROL

5V 1

SC-LX88 SC-LX78

Microphone

Tripod

Make sure there are no obstacles between the speakers and the microphone.

If you have a tripod, use it to place the microphone so that it’s about ear level at your normal listening position. If

you do not have a tripod, use some other object to install the microphone.

Install the microphone on a stable floor. Placing the microphone on any of the following surfaces may make

accurate measurement impossible:

! Sofas or other soft surfaces.

! High places such as tabletops and sofa tops.

The Full Auto MCACC display appears once the microphone is connected.

Speaker System : 7.2.2ch TMd/FW

1a.Full Auto MCACC

A/V RECEIVER

Exit Return

START

EQ Type : – – –

SP to ceiling : 3.00m

MCACC : M1.MEMORY 1

Dolby Enabled Speaker

: NO

Measurement Type : Basic

! If you leave the GUI screen for over five minutes, the screen saver will appear.

3 Press MAIN RECEIVER to switch the remote control to the receiver operation mode.

4 Select the parameters you want to set.

If the speakers are connected using any setup other than 7.2.2ch TMd/FW, be sure to set Speaker System

before the Full Auto MCACC Setup. See Speaker system setting on page 103 .

! Speaker System – Shows the current settings. When this is selected and ENTER is pressed, the speaker

system selection screen appears. Select the proper speaker system, then press RETURN to return.

If you are planning on bi-amping your front speakers, or setting up a separate speaker system in another

room, read through Speaker system setting on page 103 and make sure to connect your speakers as neces-

sary before continuing to step 4.

! EQ Type – When you select Expert for Measurement Type, set the correction method of the frequency char-

acteristics of the viewing environment. Usually, set SYMMETRY. For details, see Automatic MCACC (Expert)

on page 95 .

! MCACC – The six MCACC presets are used for storing surround sound settings for different listening posi-

tions. Simply choose an unused preset for now (you can rename it later in Data Management on page 101 ).

! Dolby Enabled Speaker – Select speakers that use Dolby Enabled Speaker (TFw+TBw, TFw, TMd, TBw).

When Dolby Enabled Speaker is not used, select NO (page 23 ).

! SP to ceiling – When Dolby Enabled Speaker is used, enter the height from the speaker to the ceiling (page 23 ).

! Measurement Type – When Basic is set, the minimum required measurement is performed in a short period

of time. When Expert is set, accurate and precise measurement is performed so it will take some time.

5 Select ‘START’, then press ENTER.

6 Follow the instructions on-screen.

Make sure the microphone is connected, and if you’re using a subwoofer, make sure it is switched on and set to a

comfortable volume level.

7 Wait for the test tones to finish, then confirm the speaker configuration in the GUI screen.

A progress report is displayed on-screen while the receiver outputs test tones to determine the speakers present

in your setup. Try to be as quiet as possible while it’s doing this.

If no operations are performed for 10 seconds while the speaker configuration check screen is being displayed,

the Full Auto MCACC Setup will resume automatically. In this case, you don’t need to select ‘OK’ and press

ENTER in step 7.

! With error messages (such as Too much ambient noise! or Check microphone.), select RETRY after check-

ing for ambient noise (see Problems when using the Auto MCACC Setup on page 51 ) and verifying the mic

connection. If there doesn’t seem to be a problem, you can simply select GO NEXT and continue.

Now Analyzing... 2/6

Environment Check

1a.Full Auto MCACC

A/V RECEIVER

Exit Cancel

Ambient Noise : OK

Microphone :

Speaker YES/NO :

L : YES

C : YES

R : YES

FWR : YES

SR : YES

SBR : YES

SBL : YES

SL : YES

FWL : YES

SW1 : YES

1a.Full Auto MCACC

OK RETRY

A/V RECEIVER

Exi

ancel

The configuration shown on-screen should reflect the actual speakers you have.

! If you see an ERR message (or the speaker configuration displayed isn’t correct), there may be a problem

with the speaker connection. If selecting RETRY doesn’t work, turn off the power and check the speaker con-

nections. If there doesn’t seem to be a problem, you can simply use i/j to select the speaker and k/l to

change the setting and continue.

! If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the

phase (dipole speakers, reflective speakers, etc.), Reverse Phase may be displayed even if the speakers are

properly connected.

If Reverse Phase is displayed, the speaker’s wiring (+ and –) may be inverted. Check the speaker

connections.

— If the connections were wrong, turn off the power, disconnect the power cord, then reconnect properly.

After this, perform the Full Auto MCACC procedure again.

— If the connections were right, select GO NEXT and continue.

8 Make sure ‘OK’ is selected, then press ENTER.

A progress report is displayed on-screen while the receiver outputs more test tones to determine the optimum

receiver settings.

Again, try to be as quiet as possible while this is happening. It may take 3 to 10 minutes.

Pioneer SC-LX78-S Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-LX78-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info