Bedienungsanleitung Pioneer SPH-DA130DAB (Seite 41 von 56) (Englisch)

699587

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

41En

English

Disconnect the iPhone or smartphone device.

Turn on the ignition switch (ACC ON).

If the vehicle’s air conditioner or heater is turned on, turn it off.

Switch the AV source to [Source OFF] (page 16).

Press (touch) .

Touch then .

Touch [A-EQ&TA Measurement].

Connect the microphone for acoustical measurement (sold separately) with this

product.

Plug the microphone into the AUX input jack on the back panel of this product.

NOTE

Use an extension cable (sold separately) if the cord of the microphone (sold separately) is not long

enough.

Touch [Front Left] or [Front Right] to select the current listening position.

Touch [Start].

A 10-second countdown starts.

NOTE

The Bluetooth connection is disconnected before the process starts.

Exit the vehicle and keep the doors closed until the countdown finishes.

When the countdown finishes, a measurement tone (noise) is emitted from the

speakers and Auto EQ measurement begins.

Wait until the measurement is completed.

When Auto EQ is completed, a message is displayed.

NOTE

The measurement time varies depending on the type of vehicle.

TIP

To stop the measurement, touch [Stop].

Store the microphone carefully in the glove box or another safe place.

If the microphone is subjected to direct sunlight for an extended period, high

temperatures may cause distortion, colour change, or malfunction.

You can adjust the cutoff frequency value of each speaker.

The following speakers can be adjusted:

[Standard Mode]: Front, Rear, Subwoofer.

[Network Mode]: High, Mid, Subwoofer.

Adjusting the cutoff frequency value

NOTE

[Subwoofer Settings] is available only when [Subwoofer] is [On].

1 Press (touch) .

2 Touch then .

3 Touch [Crossover] or [Subwoofer Settings].

4 Touch or to switch the speaker.

5 Drag the graph line to set the cutoff position.

6 Drag the lowest point of the graph to set the cutoff slope.

The following items can also be set.

The menu items vary according to the source.

Switches the subwoofer phase between normal and reverse position.

LPF/HPF

Switches the LPF/HPF setting to [On] or [Off]. When it is turned off, the high-pass

filter or low-pass filter of each speaker can also be turned on by touching the

graph lines.

Video settings

[Time Per Photo Slide]

Menu Item Description

[Time Per Photo Slide]

[5sec] [10sec] [15sec]

[Manual]

Select the interval of image file slideshows on this product.

[Video Signal Setting]

Menu Item Description

[AV]

[Auto] [PAL] [NTSC] [PAL-

M] [PAL-N] [SECAM]

Select the suitable video signal setting when you connect

this product to an AV equipment.

[AUX]

[Auto] [PAL] [NTSC] [PAL-

M] [PAL-N] [SECAM]

Select the suitable video signal setting when you connect

this product to an AUX equipment.

[Camera]

[Auto] [PAL] [NTSC] [PAL-

M] [PAL-N] [SECAM]

Select the suitable video signal setting when you connect

this product to a rear view camera.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer SPH-DA130DAB Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SPH-DA130DAB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info