Bedienungsanleitung Pioneer VSA-AX10i-S (Seite 69 von 104) (Englisch)

574062

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Using other functions

Chapter 8

Using other functions

Making an audio or a video recording

You can make an audio or a video recording from an

audio or video source connected to the amplifier (such as

a CD player or TV).

Keep in mind you can't make a digital recording from an

analog source or vice-versa, so make sure the

components you are recording to/from are hooked up in

the same way (see Connecting your equipment on

page 12 for more on connections).

You can record using composite and S-video

connections interchangeably, but you won’t be able to

record sources connected to the component video

inputs. See About the video converter on page 20 for more

on this.

For more information about video connections, see

Connecting a VCR or DVD recorder on page 18 and

Connecting other video sources on page 19.

1 Select the source you want to record.

Use the INPUT buttons (or the INPUT SELECTOR dial on

the front panel).

2 Select the input signal (if necessary).

Press SIGNAL SELECT to select the input signal

corresponding to the source component (see Selecting

the input signal type on page 44 for more on this).

3 Prepare the source you want to record.

Tune to the radio station, load the CD, video, DVD etc.

4 Prepare the recorder.

Insert a blank tape, MD, video etc. into the recording

device and set the recording levels.

Refer to the instructions that came with the recorder if

you are unsure how to do this. Most video recorders set

the audio recording level automatically—check the

component's instruction manual if you're unsure.

5 Start recording, then start playback of the source

component.

Note

• The amplifier's volume, tone (bass, treble, Midnight,

Loudness), and surround effects have no effect on

the recorded signal.

• Some digital sources are copy-protected, and can

only be recorded in analog.

• Some video sources are copy-protected. These

cannot be recorded.

Monitoring your recording

You can listen to (monitor) the recording as it’s being

made if you’ve connected a cassette deck with a

monitoring function to the TAPE 2 MONITOR jacks on

the rear panel.

• Press TAPE 2 MONITOR to switch between the

recorded signal and the original source signal.

With the remote, you may need to press on the

Home menu ( ) first before reaching the amplifier

menu screen shown below (use the / (cursor left/

right) soft keys to go to the previous/next menu screen).

Tip

• To record the tape 2 monitor signal to a recorder

connected to the CD-R/TAPE 1 inputs, select any

input (except CD-R/TAPE 1) and switch the tape 2

monitor on.

AMPLIFIER

3/3

SB CH

MODE

INPUT

STATUS

INPUT

AT T

SPEAKER

A/B

VIDEO

SELECT

TAPE2

MONITOR

DISPLAY

DIMMER

AMPLIFIER

CONT

PHONES

SP SYSTEM

A/B

SIGNAL

SELECT

VIDEO

SELECT

TAPE2

MONITOR

STREAM

DIRECT

SETUP

MIC

SB CH

MODE

DIGITAL IN

S-VIDEO VIDEO

VIDEO INPUT

AUDIOLR

MIDNIGHT

LOUDNESS OPTIONTONE DIGITAL NR INPUT ATT

SELECT

CH LEVEL

ACOUSTIC

CAL.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSA-AX10i-S Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSA-AX10i-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info