Bedienungsanleitung Pioneer VSA-AX10i-S (Seite 81 von 104) (Englisch)

574062

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Other connections

• Windows

98SE – Select Multimedia, and then

select Audio. Choose PIONEER AV Receiver/

Amplifier from the drop down menu.

• Windows

Me/Windows

2000 – Select Sound

and Multimedia and then select Audio. Choose

PIONEER AV Receiver/Amplifier from the drop

down menu.

You will also need to make sure the correct speaker

setting is selected with the audio software you’re using.

Please refer to the manual that came with the software to

make these settings.

6 Turn up the volume control on your computer

and this amplifier.

You may want to start with a fairly low volume on this

amplifier and turn it up as necessary after you’ve checked

your levels.

7 Start playback of a source on your computer.

8 If necessary, press SIGNAL SELECT to choose the

number of channels you’ll hear.

See Selecting USB and multichannel analog input

channels on page 45 for more on this.

Note

• Windows

XP, Windows

2000, Windows

Millennium Edition and Windows

98 Second

Edition operating systems have been tested for

compatibility with this interface, but depending on

your computer setup, you may find that your system

is not compatible.

• This USB interface supports up to 8 channels of

audio.

• Make sure you use a USB cable that connects from

an A-type connector (from your PC) to a 4-pin B-type

connector (to the amplifier).

• The USB specification is version 1.1 compatible, and

the USB Audio Class specification is 1.0 compatible.

• You won’t be able to control this amplifier using your

computer (and vice-versa).

• Sampling formats up to 48kHz can be heard using

the USB connection (formats above 48kHz sampling

must be downsampled).

• Any computer alert sounds will also be heard

through the speakers unless you switch them off

from the computer’s control panel.

• You won’t be able to hear the audio from the USB

connection through the digital outputs of this

amplifier.

• Even when the amplifier is switched off, it will remain

selected in your speaker settings.

• Note that using hubs or extensions may cause

connection problems.

Caution

• Make sure you don’t switch off the computer or

unplug the USB cable during playback.

• To prevent noise being output, don’t use other

software on your computer during playback.

• Pioneer is not responsible for computer system

damage, software crashes or failures, or any other

possible computer problems due to this

configuration.

Microsoft Windows

XP, Windows

2000, Windows

Millennium Edition, Windows

NT and Windows

Second Edition are registered trademarks of Microsoft

Corporation, Inc.

Connecting a PC for Advanced

MCACC output

If you use the Professional Acoustic Calibration EQ (see

page 57) to measure the reverb characteristics of your

listening room, you can check the results graphically

using a computer connected to this amplifier. Use a

commercially-available RS-232C cable to connect the RS-

232C jack on your computer to the 9-pin RS-232C jack on

the back panel of this amplifier (the cable must be cross

type, female–female).

The software to output the results is available from the

support area of the Pioneer website (www.pioneer-

eur.com/files/support/MCACC/software.html).

Instructions for using the software are also available

here. If you have any questions about the software,

please contact the Pioneer Service Center specified on

your warranty card.

Please make sure your system meets the following

requirements:

• Operating system must be Windows

XP, Windows

2000, Windows

Millennium Edition, Windows

Second Edition, or Windows

NT 4.0 (Service pack 6).

• CPU must be at least Pentium 3 / 300MHz or AMD K6

/ 300MHz (or equivalent) with at least 128MB of

memory, and your monitor must be able to display a

minimum resolution of 800x600.

• An RS-232C port connector is necessary for

graphical output. Refer to the operating instructions

and/or the PC manufacturer for more information on

making the proper port settings.

• System must have internet access.

• Connect your computer to the RS-232C jack on

the rear panel of the amplifier.

Make sure that the amplifier and all connected

components are switched off and disconnected from the

power outlet when you do this.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSA-AX10i-S Seite 81

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSA-AX10i-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info