455217
38
Zoom out
Zoom in
Vorherige Seite
1/128
Nächste Seite
Basic Setup04
38
En
Select Normal (Surround back), Speaker B,
Front Bi-Amp or ZONE 2 for the Surr Back
System setting according to connections to
the surround back speaker terminals.
4 Follow the instructions on-screen.
Make sure the microphone is connected, and if
you’re using a subwoofer, make sure it is switched
on and set to a comfortable volume level.
5 Wait for the test tones to finish, then
confirm the speaker configuration in the GUI
screen.
A progress report is displayed on-screen while
the receiver outputs test tones to determine the
speakers present in your setup. Try to be as
quiet as possible while it’s doing this.
1
If no operations are performed for 10 seconds
while the speaker configuration check screen
is being displayed, the Auto MCACC Setup will
resume automatically. In this case, you don’t
need to select ‘OK’ and press ENTER in step 6.
•With error messages (such as Too much
ambient noise! or Check microphone.)
select RETRY after checking for ambient
noise (see Problems when using the Auto
MCACC Setup below) and verifying the mic
connection. If there doesn’t seem to be a
problem, you can simply select GO NEXT
and continue.
The configuration shown on-screen should
reflect the actual speakers you have.
If you see an ERR message (or the sp eaker
configuration displayed isn’t correct), there
may be a probl
em wit
h the speaker
connection.
If selecting RETRY doesn’t work, turn off
the power and check the speaker
connections. If there doesn’t seem to be a
problem, you can simply use / to select
the speaker and / to change the
setting and continue.
•If Reverse Phase is disp layed, the
speaker’s wiring (+ and –) may be inverted.
Check the speaker connections.
2
If the connections were wrong, turn off the
power, disconnect the power cable, then
reconnect properly. After this, perform the
Full Auto MCACC procedur e again.
6 Make sure ‘
OK
’ is selected, then press
ENTER
.
A progress report is displayed on-screen while
the receiver outputs more test tones to
determine the optimum receiver settings for
Channel Level, Speaker Distance, Standing
Wave and Acoustic Cal EQ.
Again, try to be as quiet as possible while this
is happening. It may take 3 to 10 minutes.
Note
1 Do not adjust the volume during the test tones. This may result in incorrect speaker settings.
Now Analyzing... 2/10
Environment Check
1a.Full Auto MCACC
A/V RECEIVER
Exit Cancel
Ambient Noise : OK
Microphone :
Speaker YES/NO :
L : YES
R : YES
C : YES
1a.Full Auto MCACC
SR : YES
SBR : YES
SBL : YES
SL : YES
SW : YES
10
OK RETRY
A/V RECEIVER
Exit Cancel
2If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the phase
(dipole speakers, reflective speakers, etc.), Reverse Phase may be displayed even if the speakers are properly
connected. If this happens, select GO NEXT and continue.
VSX-1019_KU.book 38 ページ 2009年2月17日 火曜日 午前11時56分
38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Pioneer VSX-1019AH-K wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Pioneer VSX-1019AH-K

Pioneer VSX-1019AH-K Bedienungsanleitung - Deutsch - 127 seiten

Pioneer VSX-1019AH-K Bedienungsanleitung - Holländisch - 127 seiten

Pioneer VSX-1019AH-K Bedienungsanleitung - Französisch - 127 seiten

Pioneer VSX-1019AH-K Bedienungsanleitung - Italienisch - 127 seiten

Pioneer VSX-1019AH-K Bedienungsanleitung - Spanisch - 127 seiten

Pioneer VSX-1019AH-K Bedienungsanleitung - Schwedisch, Norwegisch, Finnisch - 251 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info