Bedienungsanleitung Pioneer VSX-1019AH-K (Seite 109 von 128) (Englisch)

455217

109

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Additional information 12

109

Remote control

HDMI

Symptom Remedy

Cannot be remote controlled. • Set a 5-digit preset code corresponding to the receiver to be operated in the

remote control (see Operating multiple receivers on page 73).

• Check whether the receiver’s remote control mode is properly set (see

Remote Control Mode Setup on page 101).

• Try replacing the batteries in the remote control (see Loading the batteries on

page 7).

• Be sure to operate within 7 m (23 feet) and a 30º angle of the remote sensor

on the front panel (see Operating range of remote control unit on page 13).

• Check that there are no obstacles between the receiver and the remote

control.

• Make sure that there is no fluorescent or other strong light shining on to the

remote sensor.

• Check the connections of the CONTROL IN jack (see Operating other Pioneer

components with this unit’s sensor on page 32).

Other components can’t be

operated with the system

remote.

• If the battery ran down, the preset codes may have been cleared. Re-enter the

preset codes.

• The preset code may be incorrect. Redo the procedure for entering preset

codes.

Symptom Remedy

The HDMI indicator blinks

continuously.

• Check all the points below.

No picture or sound. • This receiver is HDCP-compatible. Check that the components you are

connecting are also HDCP-compatible. If they are not, please connect them

using the component or composite video jacks.

• Depending on the connected source component, it’s possible that it will not

work with this receiver (even if it is HDCP-compatible). In this case, connect

using the component or composite video jacks between source and receiver.

• If the problem still persists when connecting your HDMI component directly

to your monitor, please consult the component or monitor manual or contact

the manufacturer for support.

• If video images do not appear on your TV or flat panel TV, try adjusting the

resolution, DeepColor or other setting for your component.

• If ‘NOT SUPPORT’ appears in the receiver’s display, try adjusting the

resolution, DeepColor or other setting for your component.

• While analog video signals are being output over HDMI, use a separate

connection for audio output.

• When this receiver reproduces MULTI CH IN audio sources with the HDMI

setting set to THROUGH, you cannot hear audio output from all channels. In

this case, make a digital or analog audio connection.

• To output signals in DeepColor, use an HDMI cable (High Speed HDMI™

Cable) to connect this receiver to a component or TV with the DeepColor

feature.

No picture. • Try changing the Resolution setting (in Setting the Video options on page 67).

VSX-1019_KU.book 109 ページ２００９年２月１７日　火曜日　午前１１時５６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-1019AH-K Seite 109

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-1019AH-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info